SIMES simG71 Instrucciones De Empleo página 10

ENGLISH
correctly and cannot be deflected/misfired towards operator
and/or any bystanders.
- During operation, debris from workpiece and fastening/
collation system may be discharged.
- Always wear impact-resistant eye protection with side
shields during operation of the tool.
- The risks to others shall be assessed by the operator.
- Be careful with tools without workpiece contact as they can
be fired unintentionally and injure operator and/or bystander.
- Ensure tool is always safely engaged on the workpiece and
cannot slip.
2. OPERATING HAZARDS
- Hold the tool correctly: be ready to counteract normal or
sudden movements such as recoil.
- Maintain a balanced body position and secure footing.
- Appropriate safety glasses shall be used, and appropriate
gloves and protective clothing are recommended.
- Appropriate hearing protection shall be worn.
- Use the correct energy supply as directed in the manual.
- Operating instructions shall direct the user on appropriate
uses of the tool. This shall include information on what
applications are allowed and which are not, and the
associated risks such as when working on the back of trucks
and moving platforms, etc.
- Operating instructions shall warn about risks associated
with selective actuation.
3. REPETITIVE MOTIONS HAZARDS
When using a tool for long periods, the operator may
experience discomfort in the hands, arms, shoulders, neck,
or other parts of the body.
- While using a tool, the operator shall adopt a suitable
but ergonomic posture. Maintain secure footing and avoid
awkward or off-balanced postures.
- If the operator experiences symptoms such as persistent
or recurring discomfort, pain, throbbing, aching, tingling,
numbness, burning sensation, or stiffness, do not ignore
these warning signs. The operator shall consult a qualified
health professional regarding overall activities.
- Residual risks relating to repetitive work hazards such as
duration of use in respect to working positions and forces
may exist. It is advised to consult EN 1005-3 and EN 1005-4
for such information.
- Any risk assessment should focus on muscular-skeletal
disorders and is preferentially based on the assumption that
decreasing fatigue during work is effective in reducing disorders.
10
4. ACCESSORY AND CONSUMABLE HAZARDS
- The operating instructions shall specify the appropriate
accessories and consumables.
- Disconnect the energy supply to the tool, such as air or
gas or battery as applicable, before changing/replacing
accessories such as workpiece contact, or making any
adjustments.
- Use only the sizes and types of accessories that are
provided by the manufacturer.
- Use only lubricants recommended by the tool manufacturer.
- Specification of the staples which can be used shall
include minimum and maximum diameter, length, and staple
characteristics, such as gauge and angle.
5. WORKPLACE HAZARDS
- Slips, trips and falls are major causes of workplace injury.
Be aware of slippery surfaces caused by use of the tool and
also of trip hazards caused by the airline hose.
- Proceed with additional care in unfamiliar surroundings.
Hidden hazards may exist, such as electricity or other utility
lines.
- This tool is not intended for use in potentially explosive
atmospheres and is not insulated from coming into contact
with electric power.
- Make sure there are no electrical cables, gas pipes etc. that
could cause a hazard if damaged by use of the tool.
6. DUST AND EXHAUST HAZARDS
If the tool is used in an area where there is static dust, it may
disturb the dust and cause a hazard.
- Risk assessment should include dust created by the use of
the tool and the potential for disturbing existing dust.
- Direct the exhaust so as to minimize disturbance of dust in
a dust filled environment.
- Where dust or exhaust hazards are created, the priority shall
be to control them at the point of emission.
7. NOISE HAZARDS
- Unprotected exposure to high noise levels can cause
permanent, disabling, hearing loss and other problems such
as tinnitus (ringing, buzzing, whistling or humming in the ears).
- Risk assessment and implementation of appropriate
controls for these hazards are essential.
- Appropriate controls to reduce the risk may include actions
such as damping materials to prevent workpieces from
"ringing".