Descargar Imprimir esta página

Bosch GAS 12-40 MA Professional Manual Original página 23

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 40
Fitting the vacuuming accessories (see figure A)
The vacuum hose (30) has a clip system that can be used to
connect vacuuming accessories (combi power tool
adapter (27), curved nozzle (31), combi brush nozzle
(26)).
Fitting the curved nozzle
– Push the curved nozzle (31) onto the vacuum hose (30)
until you hear both snap fasteners (35) on the vacuum
hose engage.
– To remove the adapter, press the snap fasteners (35) in-
wards and pull apart the components.
Fitting the combi power tool adapter
The combi power tool adapter (27) consists of the Power-
Tool adapter (front part) (36) and the PowerTool adapter
(rear part) (37).
The combi power tool adapter (27) is compatible with Bosch
power tools.
With an inner diameter of 38.5 mm and an outer diameter of
45 mm, the PowerTool adapter (rear part) (37) can be used
for power tools manufactured by other brands.
Place the PowerTool adapter (front part) (36) on the Power-
Tool adapter (rear part) (37) and connect both adapters by
twisting them in opposite directions (see figure B).
Push the combi power tool adapter (27) onto the vacuum
hose (30) until you hear both push buttons (35) on the va-
cuum hose click into place.
To remove the adapter, press the push buttons (35) inwards
and pull the combi power tool adapter out of the vacuum
hose.
To separate the two adapters, loosen the connection by
twisting in opposite directions and pulling the adapters
apart.
Fitting the Combi Brush Nozzle
Push the combi brush nozzle (26) onto the vacuum
hose (30) until you hear both push buttons (35) on the va-
cuum hose click into place.
To remove the adapter, press the snap fasteners (35) in-
wards and pull apart the components.
Adjusting the Combi Brush Nozzle (see figure C)
You can use the combi brush nozzle (26) as a crevice nozzle
or brush.
Press the release button (38) and push the brush forwards
to use the combi brush nozzle (26) as a brush.
Press the release button (38) and pull the brush backwards
to use the combi brush nozzle (26) as a crevice nozzle.
Fitting the vacuum hose (see figure D)
Pull the sealing plug (23) out of the hose adapter (3).
Attach the vacuum hose (30) to the hose adapter (3) and
turn it clockwise as far as it will go.
Always seal the extraction connection with the sealing
u
plug whenever you remove the vacuum hose. This pre-
vents dust from escaping.
Bosch Power Tools
Note: The friction generated by the dust in the vacuum hose
and accessory during extraction causes an electrostatic
charge that the user may experience as static discharge (de-
pending on environmental factors and their physiological
state).
Bosch generally recommends using an anti-static vacuum
hose (accessory) to vacuum up fine dust and dry materials.
Attaching the Vacuum Hose to the Dust Extractor
(see figure E)
Wrap the fitted vacuum hose (30) into the compartment for
the vacuum hose. Pull up both pull straps (17) and hook
them into the fastening openings (18).
Changing the Fleece Filter Bag (dry extraction)
A fleece filter bag (33) must be used for the dry extraction of
dust class M materials.
Insofar as materials with or without an exposure limit of
3
≥ 1 mg/m
(dust class L materials) are extracted, these can
be sucked straight into the container.
Note: Switch off the automatic filter cleaning when using the
fleece filter bag (see "Automatic/Manual Filter Cleaning
(see figure L)", page 25).
The dust extractor contains dust
WARNING
particles that pose a risk to health.
Emptying and maintenance procedures, including the
disposal of dust containers, should only be carried out by
professionals. Suitable protective equipment is re-
quired. Do not operate the vacuum cleaner unless the
complete filter system is correctly inserted. Otherwise,
you are putting your health at risk.
Inserting/Removing the Fleece Filter Bag
(see figures F−G)
Open the catches (19) and remove the top part of the dust
extractor (16).
For inserting put the fleece filter bag (33) on the fleece filter
bag holder (32) and insert the fleece filter bag (33) with the
fleece filter bag holder (32) into the container (1).
For removing close the opening of the full fleece filter bag by
pulling the catch. Pull the sealed fleece filter bag (33) out of
the fleece filter bag holder (32) and remove it from the dust
extractor.
Put the top part of the dust extractor (16) back on and con-
nect the container (1) with the top part of the dust
extractor (16) by closing the catches (19).
Attaching the L-Boxx (see figure H)
You can attach an L-Boxx to the top part of the dust extractor
for transporting the extractor and to provide space-saving
storage for extractor accessories and/or the power tool.
Attach the vacuum hose to the dust extractor (see figure E).
Click the L‑Boxx onto the holders (13).
Do not use the dust extractor with an L-Boxx attached.
u
This will raise the dust extractor's centre of gravity. The
extractor may tip over. There is a risk of injury and dam-
age if you do this.
English | 23
1 609 92A 91Y | (02.02.2024)

Publicidad

loading