DynaTrap DT1100 Manual Del Propietário

OWNER'S MANUAL
FLYING INSECT TRAP
MODEL: DTl 100
Thank you for purchasing the
DYNATRAP® flying insect trap!
IMPORTANT SAFETY INSTRUCTIONS
WARNING, When using electric appliances, basic precautions should always be followed, including the following:
- To disconnect, turn all controls to the off ("0") position, then remove plug from outlet.
- Unplug from outlet when not in use and before servicing or cleaning.
- To reduce the risk of electrical shock, do not put appliance in waler or other liquid.
- This appliance is provided with double insulation. Use only identical replacement ports.
- Connect only too circuit that is protected by o ground-fault circuit-interrupter (GFCI).
See instructions for Servicing of Double-Insulated Appliances.
INSTRUCTIONS FOR DOUBLE-INSULATED, CORD-CONNECTED APPLIANCES:
In o double-insulated appliance, two systems of insulation ore provided instead of grounding. No grounding means
is
provided
on o double-insulated appliance, nor should o means for grounding be added to the appliance. Servicing of o double-insulated
appliance requires extreme core and knowledge of the system, and should be done only by qualified service personnel.
Replacement ports for o double-insulated appliance must be identical to those ports in the appliance.
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions before using the DYNATRAP® Insect Trap and keep for future reference.
I. Always turn unit off and disconnect plug before servicing, cleaning, or changing bulb.
2. Do not mount the unit near heat, gos, oil or other flammable materials.
3. Mount product out of reach from children.
4. Never operate this product ii ii hos o damaged cord or plug, if it is not working properly, if it hos been dropped or
damaged, or if it hos been dropped into water.
5. This product is equipped with 2-conductor cord and 2-prong polarized plug os o safety feature. This plug will lit in o
polarized outlet only one way. If the plug does not fully fit in the outlet, then reverse the plug. If
it
still does not fit,
then contact o qualified electrician. To reduce the risk of electrical shock, only plug into o proper~ installed outlet.
Do not attempt to defeat this safety feature.
6. Do not insert fingers or any foreign objects into the unit while it is connected to on electrical outlet.
7. Collected insects within the unit may contribute to fire, so clean insects from the unit frequently.
8. Do not clean this product with water spray. Do not place where it con foll into water, or near flommoble materials.
9. Do not touch fan while in motion.
I 0. Do not abuse cord--never carry or hong unit by cord or yank ii to disconnect from receptacle. Keep cord away from heat,
oil, or sharp edges.
11 . Extension cords used with this product must be marked with suffix letters "W-A" and with a tag stating "Suitable for Use
with Outdoor Appliances".
12. Use only extension cords that hove plug and receptacles that match the product plug. Replace or repair damaged cords.
INSTALLATION
&
OPERATING INSTRUCTIONS
I. Unpack unit. Save carton for off-season storage (if needed).
2. If hanging or mounting the unit, place approximately 3-6 feel above the floor/ground level for optimal catch role and easy
access for cleaning.
3. For weekly cleaning, remove the screw securing the retaining cage and then twist the cage clockwise. Remove the damper by
grasping the crossbar near the edge of the damper. Pull up firmly. Remove any buildup from the inside of the retaining cage
and fan with o brush (included). Replace damper, snop firmly into place.
4. If mounting the unit to o wall, install the mounting bracket lo the side of the DTl 100. This bracket slides into side wall of
the DTllOO.
5. Plug cord into on outdoor outlet or UL listed extension cord os described in "IMPORTANT SAFETY INSTRUCTIONS".
6. For best catch results leave unit on at all times, except when cleaning or servicing.
7. Catch rote activity will be higher at night. For best catch results it is recommended to keep the unit away from competing light
sources. Intended for household use only.
CLEANING
Frequent cleaning will prolong the life of the unit, ensure fire prevention and provide for more efficient operation.
1. Be sure to clean the unit once per week
2. Switch the unit off and unplug before cleaning
3. For week~ cleaning, remove the screw securing the retaining cage and then twist the cage clockwise. Remove the damper by
grasping the crossbar near the edge of the damper. Pull up firm~. Remove ony buildup from the inside of the retaining cage and
fan with o brush (included). Replace damper, S11op firmly into place.
4. For major cleaning, remove the lour screws securing the fan housing to the light housing. After removing the screws, gently
pull the fan housing away from the light housing. Using o soft brush, remove dirt and debris from the light housing. Once the
cleaning process has been completed, align the screw holes in the fan housing with the screw holes in the lighting unit and
tighten the screws to the hose of the lighting unit.
5. When replacing the retaining cage - DO NOT press/ push against the screen windows.
REPLACING BULB
The Light bulb life expectancy is approximately 3,000 hours (or about 4 months), and should be replaced regularly to ensure
optimal UV effectiveness. Even though the bulb's light may be visible to you, its ability to attract insects diminishes over time.
1. Turn power switch to "off" position. UNPLUG UNIT, and allow bulb to cool before replacing.
2. Remove the screw securing the retaining cage and then twist the cage clockwise. Turn the unit upside down.
3. Remove the lour screws securing the Ion housing to the light housing. After removing the screws, gently pull the Ion housing
away
from the light housing. Using o soft brush, remove dirt and debris from the light housing. Once the cleaning process hos
been completed, untighten the screw securing the hose of the light bulb to the light housing. Slide the metal bracket to the side.
Cover the bulb with o cloth to protect your finger and hand. Grasp the bulb (with your hand and fingers protected by the cloth)
and gently pull the bulb from the socket.
4. Remove any debris from the lamp socket with o brush before inserting the new bulb. Replace the metal plate over the hose of
the bulb and lighten the retaining screw.
5. Align the screw hales in the Ion housing with the screw holes in the lighting unit and tighten the screws to the hose of the
lighting unit.
6. Replace the retaining coge at the bottom of the unit.
Replacement fluorescent bulbs con be found at your local retailer
or con be ordered directly from
DYNNt11C.
by colling
1-877-403-TRAP (8727) or visiting www.dynotrap.com
HOW THE DYNATRAP® INSECT TRAP WORKS
Flying insects ore attracted to the unit by UV light and CO2 that
is generated by the phato-cotolysis between the UV lamps and
special TI02 coating. The Ion then pulls the insects into the screened
hose, trapping them until they dehydrate and die. The hose con be
removed, allowing the contents to be periodically emptied into
the trash. The see-through screen shows the insects trapped in the
compartment, alerting you when the net needs ta be emptied.
TROUBLESHOOTING
Problem: Possible cause: Corredion:
Bulb does not illuminate I. No electrical power. 1. Check plug and receptacle and fuse or circuit breaker.
and fan does not spin. 2. Check to make sure power is switched to the "on" position.
Bulb illuminates, but fan 1. Shorted fan. I.UNPLUG UNIT: Examine fan to see that
ii is
free from
does not spin. foreign material, dirt or build-up of dead insects. dean unit as
in "CLEANING" section.
Fon spins, but bulb does 1. Bulb not seated 1. Check all sockets for proper bulb seating and alignment.
not illuminate. properly. 2. Replace bulb ii needed following instructions under "Replacing
2. Burnt out bulb. Bulb".
LIMITED WARRANTY
~ C. warranties ta the original purchaser that this product is free from defective materials and
workmanship. This warranty is limited to remedy any defective part for a period of one year from date of
original date of purchase. Retain your original receipt as proof of purchase. This warranty does not apply
ta the light bulb, nor to, in our judgment, misuse or abuse. If this unit has been altered, no warranty is in
force. This warranty does not apply if this unit is purchased outside the United States, excluding Canada
and Mexico. In no case shall ~ IC. be liable for any accidental, punitive, consequential, or any other
damages af any kind for breach of this or any other warranty, expressed or implied, whotsoever. Some
states do not allow limitation on how long an implied warranty lasts, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
that vary from state to state.
PARTS & ACCESSORIES AVAILABLE
PART DESCRIPTION
41050 7-Wott Replacement Fluorescent Bulb (I piece)
41052 Fon Blade and DC Motor Ultra-Long Life Replacement
41053 Retaining Cage
41059 Woll Mount Brocket
41061 Lorge Capacity Net (lo be used instead of the Retaining Cage, suitable for extra large catch performance)
Dynamic Solutions Worldwide, LLC
12247 W. Fairview Ave. Milwaukee, WI 53226
Phone: 414-431 -2819
Toll free: 1-877-403-TRAP (8727)
Toll free fax: 877-403-3293
Email: dynatropinfo@dsw-llc.com
Visit us online at www.dynotrop.com
©
Dynamic Solutions Worldwide, LLC
SAVE THESE INSTRUCTIONS
lntertek