Publicidad
Idiomas disponibles
Idiomas disponibles
REF. 53948
EN
INSTRUCTION MANUAL
PRODUCT'S PRESENTATION
This high-pressure cleaner with 2400W engine power
is ideal for cleaning bicycles, vehicles and other out-
door equipment, as well as patios, terraces, greenhou-
ses, etc. It is a highly specialized device that is particu-
larly safe and reliable. It includes an 8m high-pressure
hose, 1 turbo nozzle, copper motor, spray gun, 1 trans-
parent water connector, foam producer, patio cleaner,
1 rim brush, 1 fix brush and a 5m power cord.
SAFETY INSTRUCTIONS
WARNING! Read all safety warnings and instruc-
tions. Failure to comply with the warnings and instruc-
tions listed below may result in personal injury and/or
serious damage or death.
Desconecte siempre el aparato de la toma de corriente
antes de desmontarlo o de proceder a su reparación.
• Always disconnect the device from the power out-
let before disassembling or repairing it.
• Keep out of the reach of children.
• Do not remove or modify any parts of the gun or
the appliance.
• Do not use the appliance if you are tired or under
the influence of drugs or alcohol.
• Do not stand on unstable surfaces. Always keep
your feet well supported and balanced.
• Always place the appliance on a stable surface
when using, transporting, assembling or dismant-
ling it.
• This appliance must not be connected to a drin-
king water supply.
• Do not knock the appliance when transporting it
from one place to another.
• Keep away from the nozzle.
• Never aim the high-pressure spray at people, ani-
mals or yourself.
• Never put your hand or fingers over the spray tip
when the appliance is in operation.
• Always put the safety catch in its safety position,
even when you stop the spray for a few moments.
• Do not disconnect the high-pressure discharge
when the system is pressurized. To depressurize
the appliance, disconnect the power supply and
the water connection, then press the trigger 2 or
3 times.
• Do not leave the gun trigger permanently depres-
sed.
• This appliance has two insulation systems, a dou-
ble-insulated appliance has no grounding and no
grounding must be installed on the appliance.
• Never operate the appliance if all components are
not properly connected to it.
• Do not operate the high-pressure cleaner without
any of the parts or with damaged parts.
• Use only the nozzle supplied with this appliance.
• Periodically check the appliance and repair or re-
place any damaged or worn parts immediately.
• Never leave the machine unattended while it is in
operation.
• Always hold the gun and lancet firmly when star-
ting to use the appliance and as well as while
using it.
• The high-pressure cleaner is not intended for use
with hot water. Never connect the appliance to a
hot water outlet as this will significantly reduce the
life of the pump.
• Do not store the high-pressure cleaner outdoors
or where it may freeze. The pump will be seriously
damaged.
• Release the trigger when switching between high-
and low-pressure modes.
• Keep the hose away from sharp objects.
• Do not spray flammable liquids.
• Use only extension cords with electrical specifica-
tions equal to or greater than the appliance spe-
cifications.
• Store inside when not in use.
• To reduce the risk of electric shock, keep all con-
nections dry and off the ground and do not touch
plugs with wet hands.
• This appliance is not intended for use by persons
(including children) whose physical, sensory or
mental abilities are reduced, or who lack experien-
ce or knowledge.
• This product should not be used by children.
• To ensure the safety of the appliance, use only
original spare parts supplied or approved by the
manufacturer.
• Ensure that the water inlet pressure is between
0.01MPa and 0.4MPa.
• Unplug the appliance from the mains before carr-
ying out maintenance operations.
ASSEMBLY
1. Connect the high-pressure hose to the water out-
let of the appliance.
2. Connect the spray grip to the high-pressure hose.
Before connecting the high-pressure hose to the
appliance, make sure that it is completely uns-
crewed. While the appliance is running, the hose
must not have any loops.
3. Mount the nozzle or any other equipment you wish
to use.
4. Connect the appliance to the water and power
supply
OPERATION
ADJUSTING THE TYPE OF SPRAYING
• The angle of the spray coming out of the lance
can be adjusted on some of the lancets by turning
the nozzle. This will change the type of spray from
approximately a 0° impact jet to a spray angle
greater than 60° (see image).
· 7 ·
Publicidad
