Descargar Imprimir esta página

Craftsman CMXAZBS10000F Manual De Instrucciones página 4

Correas de trinquete

Publicidad

Idiomas disponibles

Idiomas disponibles

English
CMXAZBS10000F / CMXAZBS10000J

WARNING:
Safety glasses to be worn at all times of use.
Before use, make sure all straps are free of damage and
properly threaded/tightened.
DO NOT use strap that has fraying, wear, broken or worn
stitching, tears, cuts or defective hardware. If the strap
is damaged DO NOT use it. Contact Craftsman for a
replacement.
Make sure to pull the strap long enough to securely
wrap around the cargo load. DO NOT exceed the
working load limit of the strap; taking into account
the strap, the load, the vehicle anchor points, strap
configuration and angle, etc
These straps are intended to secure loads to surfaces.
They should NEVER be used to lift, hoist or tow objects..
DO NOT over-tighten straps.
NEVER stand in direct path of a tension loaded strap.
Protect strap from damage. ALWAYS protect straps in
contact with edges, corners, protrusions, or abrasive
surfaces with materials of sufficient strength, thickness
and construction to prevent damage.
Maintain and store straps properly. Straps should
be protected from mechanical, chemical and
environmental damage.
Manufacturer / distributor is not liable for accidents
caused by material deterioration or improper use.
For more information on the distributor's warranty,
contact Craftsman at (888) 331-4569 or email info@
craftsmanstraps.com

WARNING: This product can expose you to
Chromium (Cr), which is known to the State of
California to cause cancer, birth defects or other
reproductive harm. For more information go to
www.P65Warnings.ca.gov.
OPERATION
TO TIGHTEN RATCHET STRAPS
1. With ratchet closed, thread webbing through the center
of the drum.
2. Pull webbing through, removing the slack.
3. Release the ratchet by lifting the finger release.
To tighten, raise and lower ratchet handle; do not
overtighten. (Make sure to have a minimum of 2 full
wraps of webbing around the drum.)
4. Keep ratchet in closed position to lock.
2
TO RELEASE RATCHET STRAPS
1. To unlock, pull the finger release until the ratchet is
completely flat and open.
2. Grab webbing and pull to release.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.craftsman.com/registration
1-YEAR LIMITED WARRANTY
The warranty of this product is covered by BCS International.
Visit www.craftsman.com or call
1-888-331-4569 for more information.
This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by
others. THIS LIMITED WARRANTY IS GIVEN IN LIEU OF
ALL OTHERS, INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, AND EXCLUDES ALL INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
BCS International is a licensee of Craftsman
Products are distributed by:
BCS International
1510 Brookfield Ave.
Green Bay, WI 54313
Made in China
www.craftsman.com
www.craftsmanstraps.com
© 2023, CRAFTSMAN
CRAFTSMAN® is a registered trademark of Stanley Black &
Decker, Inc.

Publicidad

loading

Este manual también es adecuado para:

Cmxazbs10000j