Descargar Imprimir esta página

EINHELL TC-VC 1825 A Manual De Instrucciones Original página 16

Aspirador en seco y húmedo

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 73
Fitting the castors (Fig. 5)
Fit the castors (14) as shown in Fig. 5.
Fitting the handle (Fig. 4)
Use a screwdriver to fi t the handle (1).
5.2 Fitting the fi lters
Important!
Never use the wet/dry vac without a fi lter.
Always make sure that the fi lters are securely
seated!
Fitting the foam fi lter (Fig. 7)
For wet vacuuming, slip the supplied foam fi lter
(16) over the fi lter basket (Fig. 2/4). The pleated
fi lter (15) already fi tted upon delivery is not suita-
ble for wet vacuuming.
Fitting the pleated fi lter (Fig. 8)
For dry vacuuming, slip the pleated fi lter (Fig. 15)
over the fi lter basket (Fig. 2/4). The pleated fi lter
(15) is suitable for dry vacuuming only.
Fitting the dirt bag (Fig. 9)
For vacuuming fi ne dry dirt it is recommended
that you also fi t the dirt bag (19). This will ensure
that the pleated fi lter (15) does not clog up so
quickly and help maintain the vacuuming power.
It also makes it easier to dispose of the dust. Slip
the dirt bag over the vacuuming hole. The dirt bag
is suitable for dry vacuuming only.
5.3 Fitting the suction hose (Fig. 10-13)
Connect the suction hose (11) to the correspon-
ding connector on the wet/dry vac, depending on
the application required.
Vacuuming
Connect the suction hose (11) to the suction hose
connector (9).
Blowing
Connect the suction hose (11) to the blow con-
nector (10).
To extend the suction hose (11), the elements
which make up the multi-part suction tube (12)
can be attached to the suction hose (11).
5.4 Suction nozzles
Combination nozzle (Fig. 13)
The combination nozzle (13) is for vacuuming so-
lids and liquids over medium to large areas.
Anl_TC_VC_1825_A_SPK13.indb 16
Anl_TC_VC_1825_A_SPK13.indb 16
GB
Crevice nozzle (Fig. 12)
The crevice nozzle (18) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are diffi cult to access.
6. Operation
6.1 On/Off switch (Fig. 2/2)
Switch position 0: Off
Switch position I: Normal mode
Switch position AUTO: Automatic mode
6.2 Dry vacuuming
For dry-vacuuming, use the pleated fi lter (15). In
addition, you can also fi t the dirt bag. (See point
5.2)
Always make sure that the fi lters are securely
seated!
6.3 Wet vacuuming
For wet vacuuming, use the foam fi lter (16) (see
point 5.2).
Check that the fi lter is securely seated at all times.
When wet vacuuming, the fl oating safety switch
(5) closes when the maximum tank level is
reached. At the same time, the suction noise of
the equipment will change and become louder.
You must then switch off the equipment and em-
pty the tank.
Danger!
The wet/dry vac is not suitable for the vacuuming
of combustible liquids. For wet vacuuming, use
only the supplied foam fi lter.
6.4 Automatic mode
Connect the power cable of your electric tool to
the automatic socket-outlet (21) and connect the
suction hose (11) to the vacuuming connector of
your electric tool. Check that the connections are
secure and air-tight.
Set the switch (2) on the wet/dry vac to position
"AUTO "(automatic mode). The moment you
switch on the electric tool, the wet/dry vac will
switch on as well. When you switch off the electric
tool, the wet/dry vac will switch off as well after a
pre-set delay.
6.5 Blowing
Connect the suction hose (11) to the blow con-
nector (10) on the wet/dry vac.
- 16 -
14.12.2023 10:16:27
14.12.2023 10:16:27

Publicidad

loading

Este manual también es adecuado para:

23.424.85