Publicidad
Idiomas disponibles
Idiomas disponibles
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
•
Combined switch for on/off and speed control A 2
- control the speed steplessly from zero to maximum by
putting less or more pressure on the trigger A t
•
Charging battery
! read the safety warnings and instructions
provided with the charger
•
Removing/installing the battery 2
•
Attaching belt clip 9
- attach the belt clip F to the drill with the supplied screw.
•
Battery level indicator q
- press the battery level indicator button G to show the
current battery level q a
! when the lowest level of the battery indicator
starts flashing after pressing button G q b, the
battery is empty
! when 2 levels of the battery indicator start flashing
after pressing button G q c, the battery is not
within the allowable operating temperature range
•
LED-light t
LED-light automatically lights on when activating the on/
off switch
- when LED-light starts flashing, the battery
protection is activated (see below)
Battery protection
•
The tool is suddenly being switched off or prevented from
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start flashing when
pressing button G q c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level q b is shown by the battery level indicator
when pressing button G; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
•
Changing direction of rotation w
- when not properly set in left/right position, switch A 2
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
•
Changing bits e
- to remove a bit, pull the locking sleeve C forward 2
- pull the locking sleeve C forward, insert the bit to the
stop into the bit holder and release the locking sleeve C
to lock the bit. e a e b e c
! only use bits with ball catch, other bits can be
used with a universal bit holder with ball catch e b
! do not use bits with a damaged shank
•
Mode selection r
- press the mode selector J to select the desired mode:
Low speed mode (L) r a
- tightening with less force and low speed
- for smaller screws
High speed mode (H) r b
- tightening with high force and speed
- for large screws and bolts
Control mode (Arrow) r c
- start slowly to assist planting the screw in the wood
- automatically increasing speed when the screw is
planted
- for long screws, especially PHILLIPS/POZIDRIV screws
! control mode is only available with forward
rotation; in reverse rotation it is used for medium
speed
! modes can only be changed after slightly pressing
the on/off switch (green LED(s) are activated) and
when the tool is at a complete standstill
Holding and guiding the tool y
•
! while working, always hold the tool at the grey-
coloured grip area(s)
- keep ventilation slots E 2 uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you
APPLICATION ADVICE
•
Use the appropriate bits
•
When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking
of the wood
•
For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
•
When screwdriving in hard wood one should pre-drill a
hole
•
For more information see www.skil.com
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
Always keep tool clean (especially ventilation slots E 2 )
•
! remove battery from tool before cleaning
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
•
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
•
Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
9
Publicidad
