cecotec DRUMFIT STATIC 6000 SEAT Manual De Instrucciones página 27

ENGLISH
Box content
- Drumfit Static 6000 Seat Recumbent Bike
- Assembly kit
Instruction manual
-
- AAA battery for console
- Floor mat
3. ASSEMBLY
Step 1
Insert the front (3) and rear (7) stabilisers into the main frame holes, as shown in Fig. 3. Then,
fit the curved washer φ8 (B), the pressure washerφ8 (C) and the cap nut M8 (D) and tighten the
assembly.
Step 2
Remove the handlebar stem (2), connect the cable as shown in Fig. 4 and, next, reinsert the
handlebar stem back into the main frame. (During this step it is possible that the piece does
not fit properly the first time, so try it several times).
Step 3
Align the handlebar stem (2) holes with the ones in the main frame. After that, put the curved
washers φ8 (B) and insert the Allen screws M8*12 (E). Secure everything with the Allen key.
Fig. 5
Step 4
Remove the console (1) by unscrewing the two screws provided. After connecting the cables
in the console, screw it back on using the Allen key. The straight plug is inserted into the data
hole, while the L-shaped plug is inserted into the heart rate hole. Fig. 6.
Step 5
First, insert the sliding guide into the saddle bracket. Then, align the holes and fix them with
the adjustment knob. Fig. 7 and Fig. 8
Step 6
When you have assembled the parts from step 5, place them on the supports of the main
frame. Align the four holes and put plain washers and Allen screws M8*40. Secure everything
with the Allen key. Fig. 9
Step 7
Put the saddle in its frame. Align the four holes and put four plain washers (A) and four Allen
52
screws M8*12 (E). Secure everything with the Allen key. Follow the same procedure to install
the backrest. Fig. 10
Step 8
Align the holes of the side hand grips (8) with the ones on the saddle bracket. Next, put two
φ
curved washers 8 (B) and two Allen screws M8*50 (G), and fix them with plain washers
(A), pressure washers (C) and cap nuts (D). After that, connect the cables as shown in Fig. 11
Step 9
1. Take the pedals (5) and remove the pre-fixed nut.
2. Put them in the frame. The left pedal is tightened counterclockwise. Make sure that you
have put each pedal on its corresponding side. The reference (right/left) is taken as if the
user was sitting on the saddle. The left pedal is marked with an "L", the right pedal with an
"R". Fig. 12
Step 10
Adjusting the bike. Both ends of the rear stabiliser can be rotated to adjust the feet. In this way,
the machine will be level and stable when in use. Fig. 13
4. OPERATION
Getting on and off the bicycle
- Before getting on the bicycle, make sure the pedals are properly attached. Stand next to
the bike and pass the leg that is closer to it over the frame to sit on the saddle; then, insert
your feet in the pedals.
- To get off the exercise bike, do the previous step in reverse order.
Replacing the console battery
1. Remove the console from its bracket.
2. Open the battery compartment; replace the old battery with a new one and close it again.
(Positive and negative poles must be aligned).
3. Return the console to its bracket.
The type of battery used is AAA.
Console functions
- TMR (training duration): it shows the current duration of the training session. Range:
00:00-99:00 (minutes: seconds)
- SPD (speed): it shows the current speed of the bike. Range: 0-999.9 km/h.
- DIS (distance): it shows the distance travelled during training. Range: 0-99.99 km/h.
- CAL (calories burned): it shows the calories burned during training. Range: 0-999.9 kcal.
ENGLISH
φ
8
53
DRUMFIT STATIC 6000 SEAT