Sears Kenmore 25102 Serie Manual De Uso Y Cuidado página 15

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

if you experience
Washer
not draining/
spinning,
loads are
still wet, or spin light
remains
on (;ndicating
that the washer
was
unable
to pump
out
water
within
10 minutes)
(cont.)
Dry spots on load
after
cycle
Incorrect
or wrong
wash or rinse
temperatures
Load not rinsed
TROUBLESHOOTING
First try the solutions
suggested
here for assistance
and to possibly
avoid
a service
call.
PosslbJe causes
Check plumbing
for correct
drain
hose
installation.
Drain hose extends
into
standpipe
farther
than 4.5" (114 mm).
Too much detergent
causing
suds to
slow or stop draining
and spinning.
High speed spins extract
more
moisture
than traditional
top-load
washers.
Check for proper
water
supply.
Check for proper
water
supply.
Not using HE detergent
or using too
much HE detergent.
Washer
not loaded
as recommended.
Sand, pet hair, lint,
Heavy
sand, pet hair, lint, and
etc. on load after
detergent
or bleach
residues
may
washing
require
additional
rinsing.
Load is tangling
Washer
not loaded
as recommended.
Not cleaning
or
removing
stains
Added
more water
to washer.
Washer
not loaded
as recommended.
SoJutlon
Check drain
hose for proper
installation.
Use drain
hose form
and securely
attach
to drainpipe
or tub. Do not tape
over drain
opening.
Lower drain
hose if the end is higher
than 96" (2.4 m)
above
the floor.
Remove any clogs
from drain
hose.
Use only HE detergent.
Always
measure
and follow
detergent
directions
for your load.
To remove
extra
suds, select Rinse/Spin.
Do not add detergent.
The high spin speeds
combined
with air flow during
the final spin
can cause items near the top of the load to develop
dry spots
during
the final
spin. This is normal.
Make
sure hot and cold inlet hoses are not reversed.
Both hoses must be attached
to both washer
and faucet,
and
have both hot and cold water
flowing
to inlet valve.
Check that inlet valve
screens are not clogged.
Remove any kinks in hoses.
Make
sure hot and cold inlet hoses are not reversed.
Both hoses must be attached
and have water
flowing
to the inlet
valve.
Both hot and cold water faucets
must be on.
Inlet valve
screens on washer
may be clogged.
Remove any kinks in the inlet hose.
The suds from regular
detergent
can keep washer
from
operating
correctly.
Use only HE detergent.
Be sure to measure
correctly.
Always
measure
detergent
and follow
detergent
directions
based
on load
size and soil level.
The washer
is bess efficient
at rinsing
when load is tightly
packed.
Load garments
in loose heaps evenly around
the washplate.
The
washer
wJJJnot rinse well if tightly
packed.
Load with dry items
only.
Use cycle designed
for the fabrics
being washed.
Add only 1 or 2 garments
after
washer
has started.
Add a Two Rinses to the selected
cycle.
See "Using Your Washer"
section.
Select a cycle with a slower
wash action
and spin speed;
however,
items will be wetter
than those using a higher
speed spin. See the
"Cycle Guide"
to match your
load with the best cycle.
Load garments
in loose heaps evenly around
the washplate.
Reduce tangling
by mixing
types of load items. Use the
recommended
cycle for the type of garments
being washed.
Washer
senses load size and adds
correct
amount
of water. This
is normal
and necessary
for clothes
to move. It is normal
for the
wash load to be not completely
covered
in water.
Added
water
lifts the laundry
off the washpiate,
resulting
in less effective
cleaning.
Washer
is less efficient
at cleaning
when load
is tightly
packed.
Load garments
in loose heaps evenly around
the washplate.
Load
with dry items only.
J
15

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido