Scheppach GS60 Traduccion Del Manual De Instrucciones Originales página 27

• Specify our part numbers as well as the type and
year of construction of the device in your orders.
• Before you connect the equipment to the power sup-
ply make sure the data on the rating plate are identi-
cal to the mains data.
m WARNING!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
8. Montage
m WARNING!
Always pull the power plug before making adjust-
ments to the equipment.
1. Mounting the support feet (Fig. C)
• Turn the chopper so that you can turn the support
feet 180°.
• Insert the axle shaft (13) into the intended position
on the support feet. (Fig. D)
2. Mounting the wheels (Fig. E/F)
• Mount both wheels as shown in Fig. F. Use the sup-
plied tool to tighten the wheel. NOTE: If the axle
rotates when tightened, use the Allen wrench (b) to
hold it in place.
• After tightening the lock nut (14), mount the wheel
cap (17) onto the wheel (7). The position is indicated
by the grooves (18).
3. Installing den collection box (Fig. G)
• Place the locking mechanism (13) on the collection
box (8) in its lowest position (Fig. G).
• Push the collection box fully into the frame.
• Press the locking mechanism (9) on the collection
box (8) back into its highest position (Fig. I).
9. Operation
Warning! The shredder can only be started if the
collection box (8) has been pushed into the frame
and the locking device (9) is in the upper position.
Note: To start the chopper, the switch for roller ro-
tation direction (11) must be set to "I".
Control panel (Fig. B)
• On switch (2): Pressing this button starts the shred-
der.
• Off switch (3): Pressing this button stops the shred-
der.
• Switch for roll rotation direction (11):
• Button „▲" - anti-clockwise: When this button is
pressed, the blade cylinder rotates anti-clockwise.
This is necessary when jammed shredding materi-
al needs to be freed. This function is only available
when the shredder is in operation.
• Button „▼" - clockwise: This button switches the
direction of the blade cylinder from anti-clockwise
back to clockwise.
• Reset-switch (12): Overload protection
Working with the shredder
Alternating with branches, shred withered garden
waste and branches that have been stored sev-
eral days to prevent the shredder from becoming
blocked.
• Make sure the collection box (8) is pushed into the
frame correctly and the locking device (9) is in the
upper position.
• Connect the shredder to the power supply.
• Turn the shredder on by using the on switch (3).
• Fill shredding material into the feed hopper and it
will be drawn in.
• Caution: If the material becomes jammed, first
press the red off switch (3) to stop the device. Push
the switch for roll rotation direction (11) downwards
to the " = " sign. Start the device by pressing the
green on switch (2). Stop the device by pressing
the red off switch (3). Remove the jammed material.
Push the switch (11) to the " - " sign. The device is
ready for operation.
• Make sure the shredder has completely shred-
ded the input material before adding new.
• Do not use your hands to push in more shredding
material. Use the special pushing device (c) or other
shredding material.
• When you have finished working with the shredder,
turn it off and disconnect it from the mains.
Emptying the collection box
• Stop the shredder using the off button (3).
• Set the locking device (9) to the lowest position.
• Pull out the collection box (8) and empty it.
• Re-insert the collection box (8) and push the locking
device (9) up again.
www.scheppach.com GB | 27