Kärcher KM 70/30 C Bp Pack Manual página 7

Device illustration
Illustration A
Carrying handle
1
Filter cleaning handle
2
Right side brush
3
Twist grip for side brush contact pressure
4
Dust suction release mechanism
5
Cover of fan for dust suction
6
Storage shelf for accessories, maximum load 5 kg
7
Star grip for push handle adjustment (2x)
8
Rechargeable battery pack
9
Charger
10
Push handle
11
Waste container seal
12
Roller brush
13
Type plate
14
Cover of battery pack holder
15
Program switch
16
Battery pack release
17
Battery pack holder
18
Lever for roller brush contact pressure (sweeping pat-
19
tern)
Dust suction seal
20
Fan for dust suction
21
Waste container handle
22
Flat fold filter
23
Fastening eyelet
24
Left side brush
25
Removable waste container
26
Initial startup
Mounting the push handle
1. Position the push handle on the device.
Illustration B
Screw
1
Push handle
2
Star grip
3
Washer
4
2. Insert the screw through the push handle holder and
push handle.
3. Put on the windshield.
4. Fit the star grip and tighten.
5. Repeat entire procedure on the opposite side.
Adjusting the push handle
1. Release both star grips.
Illustration C
Star grip
1
Push handle
2
2. Pull the push handle backwards and swivel it into the
desired position.
3. Push the push handle forward and engage.
4. Tighten the star grips.
Installing the side brush
The side brushes are supplied with the device on delivery
and must be attached to the device before initial startup.
See chapter "Changing the side brushes".
Charging/inserting the battery pack
Charge the battery pack before the initial startup.
Please observe the instructions for charging and operation
in the operating instructions and safety instructions en-
closed with the battery pack and charger.
1. Fold up the cover of the battery pack holder.
Illustration D
Battery pack holder
1
Rechargeable battery pack
2
Cover of battery pack holder
3
2. Insert the charged battery pack into the battery pack
holder, push it in up to the stop and snap it in place.
3. Close the cover of battery pack holder.
Selecting the programme
1. Turn the programme switch to the desired programme.
Illustration E
0 - device is switched off.
1
Sweeping
2
Sweep vacuuming
3
ATTENTION
Risk of damage
Packing tape, wires or similar things can damage the
sweeping mechanism.
Keep packing tape, wires or similar things away from the
device.
Note
Adjust the travel speed to the conditions in order to
achieve optimum cleaning results.
Empty the waste container at regular intervals.
Lower the side brushes to clean side edges.
Note
A bucket or other container up to a maximum of 5 kg can
be placed on the cover of the dust suction blower.
1. If necessary, secure the container to the cover with a
tensioning strap. Guide the tensioning strap through the
fastening eyelet.
2. Swing the side brushes up or down depending on the
task.
Note
Dust whirled up by the side brush is not vacuumed up.
Only use the side brushes when sweeping edges.
3. Set the program switch to sweep or sweep vacuuming.
Note
Only use the sweep vacuuming program when the floor is
dry.
4. Push the device over the surface to be swept.
Adjusting the roller brush contact pressure
1. Pull out, adjust and lower the roller brush contact pres-
sure lever.
Illustration F
Roller brush contact pressure lever
1
5 - highest contact pressure
1 - lowest contact pressure
P - roller brush raised
Note
Higher contact pressure results in increased energy re-
quirements and shorter operating times.
Note
Move the lever to the "P" position to park and transport the
device. Roller brush is fully raised and damage to the bris-
tles is avoided.
English
Operation
Sweeping
7