Failures In The Pitt ® Cooking System; Models Overview Top Side - PITT Akan Manual Del Usuario

7 Failures in the PITT cooking system
®
Note: the PITT cooking-system may only be connected by an approved installer. To ensure the safety and warranty
®
repairs may only be performed by approved professionals. You should only use original parts.
Failure Cause
A burner ignites and The control knob is not pressed
turns off again. long enough to activate the auto-
flame detection.
The control knob is not adjusted at
the correct height.
The control-button Hob is not mounted the right way
touches the sealing under the countertop.
scale.
Sealing scale is not in the center
vs. control knob.
Spark ignition Hob is not mounted the right way
remains igniting. under the countertop.
Sealing scale is not in the center
vs. control knob.
The burner doesn't The control knob is not adjusted at
ignite. the correct height.
The power plug is not in the power
socket.
Fuse malfunction / fuse in meter
cupboard is disabled.
Spark ignition is dirty or wet.
Burner parts are not properly
mounted.
Burner parts are dirty or wet.
The main gas supply is not open.
The control knob is not pressed
long enough
EN
Battery empty*
A burner does not Burner parts are not placed
burn evenly. properly.
Burner parts are dirty or wet.
Gas smell. Gas connection leaks.
There is a burner turned on, but
not inflamed.
* Depending on the model
** TS = Top Side / FS = Front Side
If the failure still remains please contact your dealer or the PITT
page 76.
Solution Chapter / Page
Press the control knob down Chapter 4 / page 18
long enough to turn between full
and low heat.
Adjust the control knob properly. Installation manual **
TS: 13 t/m 15 FS: 11 t/m 17
Adjust the control knob properly. Installation manual **
TS: 13 t/m 15 FS: 11 t/m 17
Detach sealing scale and and Installation manual **
re-stick again. TS: 20 t/m 21 FS: 16 t/m 17
Adjust the control knob properly. Installation manual **
TS: 13 t/m 15 FS: 11 t/m 17
Detach sealing scale and and Installation manual **
re-stick again. TS: 20 t/m 21 FS: 16 t/m 17
Adjust the control knob properly. Installation manual **
TS: 13 t/m 15 FS: 11 t/m 17
Put the power plug into the
power socket.
Install a new fuse or switch on
the fuse again.
Clean or dry the spark ignition. Chapter 6 / page 19
Ensure the burner parts are Chapter 6 / page 19
correctly aligned with the
centring cams.
Clean or dry the Chapter 6 / page 19
burner parts. Make sure the
outflow holes are open.
Open the main gas supply.
Press the control knob down Chapter 4 / page 18
long enough to turn between full
and low heat.
Replace battery Chapter 2 / page 16
Ensure the burner parts are Chapter 6 / page 19
correctly aligned with the
centring cams.
Clean or dry the Chapter 6 / page 19
burner parts. Make sure the
outflow holes are open.
Check the connection. Turn main
gas supply off immediately when
you're not able to fix it right
away.
Close the control knob and wait Chapter 4 / page 18
a few minutes before reigniting.
cooking customer service: See the service addresses on
®
20
8

Models overview Top Side

Akan Altar
Baluran Bennett
Bromo Cima
653
450
Cusin
Danau
Azuma Air
Baula Bely
Capital
Colo
Drum
21
EN