Manuales relacionados para PRETUL DES-52P
Resumen de contenidos para PRETUL DES-52P
- Página 1 Manual Gas brushcutter Applies for: Code Model 26104 DES-52P 52 cm (cc) Motor Read the user’s manual thoroughly CAUTION before operating this tool.
- Página 2 Contents CAUTION Technical data Fuel specifications To gain the best performance of the tool, prolong the duty life, General safety warnings for the use of make the Warranty valid if motorized necessary, and to avoid hazards of fatal injuries please read and Safety warnings for the use of a gas understand this Manual before brushcutter...
- Página 3 Technical data DES-52P Code 26104 Description Gas brushcutter Net Weight 16.3 lb Engine 52 cm (cc) Engine Rated Power 1400 W Fuel Tank 20 oz Speed 9300 RPM Cutting Capacity 17” Shaft length 54" Cutting Systems Nylon thread spool and blade Blade diameter Outer: 10"...
- Página 4 General Motor Tool safety Warnings Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. These safety gears reduce the risk Never use the tool in explosive areas or in the presence of injury.
- Página 5 Safety warnings for brushcutters • In extreme weather confirm there is no ice forming and Fuel handling condensation in the gas brushcutter. • Confirm the visibility and light conditions are adequate • Never smoke near fuel, or in the gas filling up zone or when preparing the oil mix, nor when operating the to be able to see clearly.
- Página 6 Parts Cutting Recoil thread starter Line Spark spool plug Choker lever Starter Muffler choke Harnnes Fuel tank cap Fuel ring tank Guard Apron Auxiliary Double harnnes handle Handle bar Control adjustment knob handle Straight axis Bracket Harnnes Straight ring axis Auxiliary handle Throttle...
- Página 7 Assembly Handle Guard • Separate the clamp from the straight shaft mount by • Loosen the guard fixing screws, align the guard holes with loosening the quick-adjust knob (a). those on the clamp mounted on the cutting head, and • Place the handle on the straight shaft mount. secure the assembly with •...
- Página 8 Assembly Installation of the nylon thread spool • Place the pressure plate on the cutting head (7). • Insert the Allen wrench into the side of the pressure plate to lock the shaft. • Thread the spool onto the shaft and tighten it by hand counterclockwise (8).
- Página 9 Fuel and oil Fueling the engine • Follow the safety guidelines for fuel handling (page 5). • Wait for the engine to cool down completely before fueling. • Place the brush cutter on a flat surface. • Clean around the fuel tank cap to prevent contamina- tion.
- Página 10 Start Up Starting the motor when hot • Place the brush cutter on a level surface where the blade does not contact any obstacles. • Set the switch to the “on” position (H). • Pull the starter cord (J) until the engine starts. Shut down •...
- Página 11 Maintenance • Before inspecting, cleaning, or servicing the brush cutter, turn off the engine, wait for all moving parts to stop, disconnect the spark plug cable, and remove it from the spark plug. Otherwise, you may suffer severe injuries and/or damage to the equipment.
- Página 12 Maintenance Gas brushcutter Storage In the event of storing the gas brushcutter for one month or longer, bear in mind the following considerations: • Drain all the fuel tank contents into an approved gasoline container. All the remaining fuel can be re-used in another tool that uses 2-stroke motor with a 40:1 ratio.
- Página 13 Notes ENGLISH...
- Página 14 Notes ENGLISH...
- Página 15 Authorized Service Centers In the event of any problem contacting a TRUPER Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800-018-7873 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS AGUASCALIENTES...
- Página 16 Model Brand 26104 DES-52P Warranty. Duration: 1 year. Coverage: parts, components and workmanship against manufacturing or operating defects, except if used under conditions other than normal; when it was not operated in accordance with the instructive; was altered or repaired by personnel not authorized by Truper .