EINHELL TP-CC 10 T Manual De Instrucciones Original página 30

38. Fastening screw for the cross stop
39. Eccentric lever for the blade guard
40. 2.5 mm socket head screw for the table insert
41. Slide
42. Clamping lever for the guide rail
43. Threaded sleeve
44. Nut
45. Cable holder
46. Rotary knob for the cutting width
47. Rotary knob shaft
48. Recessed head screw for the rotary knob
49. 4 mm socket head screw for the splitter
50. 2.5 mm grub screw for the splitter
51. Cover for the self-locking nut
52. Recessed head screw for the cover
53. Self-locking nut
54. Pointer for the parallel stop
55. Angle scale
56. Pointer for the blade angle
57. 3 mm socket head screw for the hand wheel
58. 3 mm socket head screw for the locking lever
59. Hexagon screw
60. Locking lever
61. 0° eccentric plate
62. 45° eccentric plate
63. Cover for the suction channel
64. Recessed head screw for the suction channel
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
Anl_TP-CC_10_SPK13.indb 30 Anl_TP-CC_10_SPK13.indb 30
GB
•
Bench-type circular saw
•
Blade guard
•
Push stick
•
Parallel stop
•
Cross stop
•
Extractor adapter
•
24 mm ring wrench
•
20/24 mm combination wrench
•
Rotary knob for the cutting width
•
Recessed head screw for the rotary knob
•
Original Operating Instructions
•
Safety Information
3. Proper use
The bench-type circular saw is designed for the
slitting and cross-cutting (only with the cross
stop) of all types of timber commensurate with the
machine's size. The equipment is not to be used
for cutting any type of round wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
The equipment is to be operated only with suita-
ble saw blades (saw blades made of HM or CV)
It is prohibited to use any type of HSS saw blade
and cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
- 30 -
27.09.2023 08:10:02 27.09.2023 08:10:02