EINHELL TP-CC 10 T Manual De Instrucciones Original página 34

•
Caution! Turn the screw (15) in the direction
of rotation of the blade.
•
Remove the outer flange and the old blade
(4) from the inner flange.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Fit and fasten the new blade (4) in reverse
order.
•
Warning! Note the running direction. The cut-
ting angle of the teeth must point in running
direction, i.e. forwards (see the arrow on the
blade guard).
•
Secure the fastening lever (19) again, then
mount and adjust the splitter, the table insert
and the blade guard (see 6.5, 6.3, 6.6).
•
Check that all safety devices are in good wor-
king order before you begin working with the
saw again.
•
Warning! Every time you change the blade,
check that the blade guard (2) opens and clo-
ses again in accordance with requirements.
Also check that the blade (4) spins freely in
the saw blade guard (2).
•
Warning! Every time that you change the
blade, check to see that it spins freely in the
table insert (6) in both perpendicular and 45°
angle settings.
•
Warning! A worn or damaged table insert (6)
must be replaced immediately (see 6.3).
•
Warning! The work to change and align the
blade (4) must be carried out correctly.
6.8 Connection for dust extraction (Fig. 11)
A connection option for dust extraction is provi-
ded at the extractor adapter (16) on the housing.
For example, you can connect a wet & dry vac
(not included with this product) to the extractor
adapter (16).
6.9 Fitting/removing the parallel stop (Fig. 12)
•
Open the two locking bolts (27) on the front
and back sides of the parallel stop (7) by tur-
ning the locking bolts (27) by 90° upwards.
•
To fit the parallel stop (7), move the position
of the guide screws (28) outwards as far as
possible so that you can mount the parallel
stop (7) alongside the saw table (1).
•
Clean any chips, dust or other dirt off the sup-
port surfaces on the parallel stop and off the
guide rail (24).
•
With the parallel stop (7) tilted by approx. 45°,
guide it by the recess onto the guide screws
(28).
Anl_TP-CC_10_SPK13.indb 34 Anl_TP-CC_10_SPK13.indb 34
GB
•
Tilt the parallel stop (7) downwards. Make
sure that the parallel stop (7) and the retai-
ning screw (29) engage with each other. The
mount of the parallel stop (7) should rest over
the entire width firmly on the guide rail (24)
and is not allowed to wobble.
•
Secure the parallel stop (7) by closing the two
locking bolts (27).
•
To remove the parallel stop (7) again, pro-
ceed in reverse order.
7. Operation
7.1 On/Off switch (Fig. 1, 13 / Item 11)
•
To turn the saw on, press the green button
„I". Wait for the blade to reach its maximum
speed of rotation before commencing with the
cut.
•
The red button "0" is covered by the switch
cover (37). To switch off the saw, press the
switch cover (37).
The motor of this equipment is protected against
overload by an overload switch (12). If the rated
current is exceeded, the overload switch (12) will
shut down the equipment.
•
Let the equipment cool down for several mi-
nutes.
•
Press the overload switch (12).
•
Press the green button „I" to switch on the
equipment.
7.2 Cutting depth (Fig. 1, 14)
Turn the hand wheel (8) to set the blade (4) to the
required cutting depth.
Warning! To reduce the risk of coming into con-
tact with the blade (4), always adjust the cutting
depth of the blade to the thickness of the work-
piece.
Rule of thumb: The blade (4) should be moved
in and out only as far as necessary for the tips
of the blade teeth to project visibly beyond the
workpiece.
Turn counter-clockwise:
Smaller cutting depth
Turn clockwise:
Larger cutting depth
- 34 -
27.09.2023 08:10:04 27.09.2023 08:10:04