Changing This Unit's Settings - Pioneer DJM-T1 Manual De Instrucciones

Changing this unit's settings

1 Press the [UTILITY (WAKE UP)] button for over 1 second.
The [UTILITY (WAKE UP)] indicator and the top of the [CH 1] channel level indicator
flash.
2 Press the [LOAD (DUPLICATE) B] button.
The setting item changes each time the [LOAD (DUPLICATE) B] button is pressed.
The flashing position of the [CH 1] channel level indicator moves downwards.
! When the [LOAD (DUPLICATE) A] button is pressed, the selection returns to the
previous setting item.
The flashing position of the [CH 1] channel level indicator moves upwards.
3 Turn the rotary selector.
Change the setting value.
! When the setting value can be switched on and off
— On: The green section of the [CH 2] channel level indicator lights.
— Off: The green section of the [CH 2] channel level indicator turns off.
! When the setting value can be switched in steps
— One's place of setting value: Value indicated by the number of segments
of the [CH 2] channel level indicator that are lit.
— Ten's place of setting value: Value indicated by the number of segments
of the master level indicator that are lit.
4 Press the rotary selector.
The settings are stored in this unit.
The [UTILITY (WAKE UP)] button flashes rapidly. Do not turn this unit's power off
while the settings are being stored.
! Storing is completed when the [UTILITY (WAKE UP)] button switches from
flashing rapidly to flashing normally.
! Press the [UTILITY (WAKE UP)] button to return to normal operation.
Setting preferences
Flashing position of [CH 1]
Options settings
channel level indicator
Cross Fader Cut Lag Very top
Cross Fader Curve Slow A Second from top
Cross Fader Curve Slow B Third from top
Cross Fader Curve Fast A Fourth from top
Cross Fader Curve Fast B Fifth from top
Generic Controller Mode Sixth from top
Mic Output To Booth Monitor Seventh from top
Eighth from top
Auto Standby
1 If the setting value is extremely small, the sound may not be completely muted even when the crossfader is positioned at the very edge.
2 If the setting value is small, the attenuation will have a gentle curve characteristic. If the setting value is large, the attenuation will have an abrupt curve characteristic.
About the auto standby function
When [Auto Standby] is set to [ON], the standby mode is set automatically if 4
hours pass with all of the conditions shown below met.
— That none of this unit's buttons or controls are operated.
— That no audio signals are input to this unit's input terminals.
— That no computer is connected by USB.
! When the [UTILITY (WAKE UP)] button is pressed, the standby mode is
canceled.
! This unit is shipped with the auto standby function turned on. If you do not want
to use the auto standby function, set [Auto Standby] to [OFF].
Checking the firmware version
1 Press the [UTILITY (WAKE UP)] button for over 1 second.
2 Press the [LOAD (DUPLICATE) A] button.
The firmware version is indicated by the segments of the channel level and master
level indicators that light.
— Number of segments of the [CH 1] channel level indicator lit: One's place
— Number of segments of the master channel level indicator lit: First decimal
place
— Number of segments of the [CH 2] channel level indicator lit: Second deci-
mal place
Example: When version "1.07" is indicated
! If the top segment of the [CH 1] channel level indicator flashes, the firmware
version is one earlier than 2.00.
Setting value Default value
0 to 52 6
0 to 32 16
0 to 32 16
0 to 32 32
0 to 32 32
ON/OFF OFF
ON/OFF ON
ON/OFF ON
1 MASTER 2
OVER OVER
9 9
5 5
3 3
1 1
0 0
- 1 - 1
- 3 - 3
- 6 - 6
- 9 - 9
- 15 - 15
- 24 - 24
dB dB
Descriptions
Adjusts the play at the edges of the crossfader (the cut lag). The cut lag can be
adjusted between 0.74 mm and 5.94 mm, in 0.1 mm units.1
Adjusts the [CH 1] side attenuation curve characteristics when the [CROSS F.
CURVE (THRU, , )] switch is set to [
Adjusts the [CH 2] side attenuation curve characteristics when the [CROSS F.
CURVE (THRU, , )] switch is set to [
Adjusts the [CH 1] side attenuation curve characteristics when the [CROSS F.
CURVE (THRU, , )] switch is set to [
Adjusts the [CH 2] side attenuation curve characteristics when the [CROSS F.
CURVE (THRU, , )] switch is set to [
Turns on and off the function for selecting effects using the effect control
buttons.
When off, the LFO CONTROL and CROSS FADER CONTROL functions can be
used.
Sets whether or not to output the microphone's audio signals from [BOOTH]
terminals.
Turns the auto standby function on and off.
].2
].2
].2
].2
27
En