DeWalt DW734 Manual De Instrucciones página 7

3-wire extension cord which has a 3-prong grounding
type plug and matching receptacle which will accept
the machine's plug. When using an extension cord,
be sure to use one heavy enough to carry the current
of the machine. An undersized cord will cause a
drop in line voltage, resulting in loss of power and
overheating. Minimum gauge for Cord sets
shows the correct gauge to use depending on the cord
length. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V 25 (7.6)
240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More not
American Wire gauge
Than More
Than
0 6 18
6 10 18
10 12 16
12 16 14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Specifications
Input 120V AC, 15 Amp
No-load speed 10000 RPM
Feed speed 24' (7.3 m) per minute
Planing height Maximum 6" (152.4 mm)
Minimum 1/8" (3.2 mm)
Planing width Maximum 12-1/2" (317.5 mm)
Planing depth Maximum 1/8" (3.2 mm) (for boards 5" (127 mm)
wide or less)
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
16 16 14
16 14 12
16 14 12
12 Not Recommended
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
Electrical Connection
Be sure your power supply agrees with the nameplate
marking. Volts, 50/60 Hz or "AC only" means your planer
must be operated only with alternating current and never
with direct current. Voltage decrease of more than 10%
will cause loss of power and overheating. All D
are factory tested, if this tool does not operate, check the
power supply.
Intended Use
This planer is designed for wood working.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Carriage Head Lock (Fig. D)
Your planer is equipped with a carriage head lock lever
located on top of the motor. This device secures the carriage
that holds the cutterhead to the four posts of your planer.
By locking the carriage to the four posts, the movement that
causes snipe is drastically minimized.
Fig. D
9
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Transporting the Planer (Fig A)

WARNING: For your own safety, it is recommended
that two people carry this machine or serious injury
could result.
When moving your planer, hold it by the side carrying
handles or by the hand indentation
2
the planer.
When transporting or storing the planer, use the cord
wrap 4 located in the back of the tool to keep the cord
in place.
Bench Mounting (Fig. E)
To facilitate bench mounting, two different sized holes
are provided on the four corners of your planer as shown in
Figure E. If mounting the planer with bolts, use the larger
English
WALT tools
e
9
6
at the base of
3
5
5