Bosch 06039B3000 Manual Original página 15

(3) Anti-clockwise rotational direction indicator
(4) Rotational direction switch
(5) "PowerLight"
(6) Battery charge indicator
(7) On/off switch
(8) Handle (insulated gripping surface)
(9) Charging connector
(10) Socket for charging connector
(11) Charger
Technical Data
Cordless Drill/Driver
Article number
Rated voltage
A)
No-load speed
Max. torque, hard/soft
screwdriving application ac-
cording to ISO 5393
Max. drilling diameter
Max. screw diameter
Weight according to
EPTA-Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation and
during storage
Rechargeable battery
Capacity
Number of battery cells
Battery charger
Article number
Charging time
Battery charging voltage
Charging current
Protection class
A) measured at 20 - 25 °C
B) Limited performance at temperatures < 0 °C
Noise/vibration information
Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1:
2
Drilling into metal: a < 2.5 m/s , K = 1.5 m/s
h
Bosch Power Tools
EasyDrill 12
3 603 JB3 0..
V= 12
-1
min 0–700
Nm 6/15
mm 6
mm 6
kg 0.95
°C 0 to +45
°C –20 to +50
Li-ion
Ah 1.5
3
1 600 A01 P1P (EU)
1 600 A01 P2B (UK)
h 3
V 15
A 0.5
/II
2
,
2
Screwdriving: a < 2.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Before any work on the power tool (e.g. maintenance,
u
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the middle
position. There is risk of injury from unintentionally
pressing the on/off switch.
Battery Charging (see figure A)
Do not use any other charger. The supplied charger is
u
matched to the lithium-ion battery that is fitted in your
power tool.
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Note: The battery is supplied partially charged. To ensure
the maximum performance of the battery, use the power ad-
aptor to fully charge the battery before first use.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool stops moving.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
The charging process begins as soon as you have inserted
the mains plug for the charger into the mains socket and the
charging connector (9) into the port (10) on the bottom of
the handle.
English | 15
2
1 609 92A 7V0 | (19.07.2022)