Commodore 1084 Modo De Empleo página 3

English
Introduction
Your monitor has been designed and
manufactured to the highest standards,
and subject to rigorous testing. Provided it
is properly operated and maintained it will
perform well for many years.
This colour monitor is suitable for use with
home and personal computers, video
recorders, LaserVision Players and TV
Tuners.
Connection to the mains (For UK only)
Your new monitor is designed to operate
from an a.c. mains supply of 220-240 volts,
50 Hz. Stabilising circuits ensure
satisfactory performance within normal
supply variations.
Important: This apparatus must be
earthed. This can be achieved by fitting a
3 pin plug. The wires in the earthed
mains lead are coloured according to
the following code:
BLUE = NEUTRAL
BROWN = LIVE
GREEN/YELLOW = EARTH
If the mains plug (or adaptor) contains a
fuse, the value of this fuse should be
3 Amp. Alternatively, if another type of
plug (not fused) is used, the fuse at the
distribution board should not be greater
than 5 Amp.
If the colours of the wires in the mains
lead do not correspond with the
coloured markings identifying the
terminals in your plug, proceed as
follows...
The BLUE wire should be connected to
the terminal marked 'N' or coloured
black.
The BROWN wire should be connected
to the terminal marked 'L' or coloured
red.
The GREEN and YELLOW wire must be
connected to the terminal in the plug
marked by 'E' or the earth symbol L, or
coloured green or green and yellow.
Before replacing the plug cover, make
certain that the cord grip is clamped
over the sheath of the lead - not simpiy
over the three wires.
1
Positioning/Ventilation
In order to prevent overheating, ensure
that the ventilation openings in the monitor
are not covered.
The monitor should not be placed near a
source of heat nor on a soft surface since
this would block the ventilation slots on
the bottom.
Movable support
You can tilt the monitor into a convenient
position with regard to the computer by
using the movable support.
Connection to the mains
You can connect your monitor to a mains
voltage of between 220 and 240 V. If the
mains voltage in your home is different
from this, consult your dealer.
Connections (rear panel)
for input of video and audio signals. Each
connector is marked with its function.
JO
nea
Mica
CVBS/L AUDIO
TTL.RGB
CVBS/L (Luminance) IN (Phono type)
CVBS (composite signal) or Luminance
input Phono plug type.
For connection of a computer or. other
CVBS sources.
CHROMA IN (phono type)
Chroma (colour signal) of the phono
plug type. For connection of a
computer.
AUDIO IN (Phono type) f
For connection of a signal source with a
sound (audio) signal output.
LCA/CVBS switch
With the LCA/CVBS switch M = you can
either choose the LCA signal or the CVBS
signal (via euroconnector or phono plug).
TTL RGB input (8 pin DIN type 270º)
For connection of a computer with a TTL
RGB output with separated
Synchronisation (TTL lavel).
Connection (left panel)
Headphones
On the left side of the monitor you will find
a 3,5 mm jack-type socket for connecting
the headphones.
Operation
EURO CONNECTOR
CVBS + RGB linear + Audio input
(Euroconnector type)
For connection of a Video Recorder,
Computer, LaserVision Player, TV Tuner,
etc. equipped with a Euroconnector.
Remark:
It you connect both RGB inputs
simultaneously the TTL RGB input
automatically has priority over the linear
RGB input.
After switching off or removing the
connection cable from the TTL source,
RGB linear will be looped in.
Furthermore you can connect a CVBS
source (computer, Video Recorder, TV
Tuner, etc.) to one of the CVBS input
sockets, but not on both input sockets
simultaneously because this might result in
picture disturbance.
Switching on ©
o Press button © (LED lights up).
Switching off ©
e Press button © again.
Picture and sound controls
available.
e Open flap (a).