Publicidad
Idiomas disponibles
Idiomas disponibles
9
Working instructions
Note:
* = not included in the scope of delivery!
Undoing
• If the screws/nuts are very tight or rusted, they must
be "loosened" with a wheel brace* or torque wrench*
Tightening
ATTENTION
The cordless impact screwdriver should only be used
for undoing screws/nuts. However, if screws/nuts are to
be tightened with the impact screwdriver, a torque limit-
er* designed for this purpose must be used as this may
otherwise damage the screw connection.
• Carefully insert the screw/nut into the thread before
tightening.
• Only tighten the screws/nuts, for which a torque speci-
fication applies (e.g. in the motor vehicle sector, by
the specifications of the vehicle manufacturer), with a
torque limiter designed for this purpose.
Torque
• Small screws*/bits* may be damaged if the torque or
the speed is set too high.
WARNING
Retighten or check the screws/nuts with a torque
wrench* to the torque stipulated by the manufacturer!
10 Cleaning and maintenance
WARNING
Have maintenance and repair tasks that are
not described in this operating manual, car-
ried out by a specialist workshop. Use only
original spare parts.
There is a risk of accident! Always perform
maintenance and cleaning work with the bat-
tery removed. There is a danger of injury! Let
the Product cool down before all mainte-
nance and cleaning tasks. Elements of the
engine are hot. There is a danger of injury
and burning!
The product can start unexpectedly and cause injuries.
–
Remove the battery.
–
Allow the product to cool down.
–
Remove the tool attachment.
10.1
Cleaning
1. Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub the
product clean with a clean cloth or blow it off with
compressed air at low pressure. We recommend that
you clean the product directly after every use.
2. Ventilation openings must always be free.
20 | GB
3. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interior.
4. Wipe any dirt off the lens with a dry cloth. Be careful
to avoid scratching the LED lamp as this can severely
reduce the light intensity.
10.2
Maintenance
The product is maintenance-free.
11 Storage
Preparation for storage
1. Remove the battery.
2. Clean and check the product for damage.
Store the product and its accessories in a dark, dry and
frost-free place that is inaccessible to children.
The optimum storage temperature is between 5°C and
30˚C.
Store the product in its original packaging.
Cover the product to protect it from dust or moisture.
Store the operating manual with the product.
12 Repair & ordering spare parts
With this product, it is necessary to note that the following
parts are subject to natural or usage-related wear, or that
the following parts are required as consumables.
ATTENTION
According to the German Product Liability Act, no liabili-
ty is accepted for damage caused by improper repairs
or by not using original spare parts.
Such work should be performed by a customer service
centre or an authorised specialists. The same applies to
accessory parts.
Spare parts and accessories can be obtained from our
Service Centre. To do this, scan the QR code on the front
page.
12.1
Ordering spare parts
Please provide the following information when ordering
spare parts:
• Model designation
• Item number
• Type plate data
Spare parts / accessories
Battery pack SBP2.0 - Article no.:
Battery pack SBP4.0 - Article no.:
Battery charger SBC2.4A - Article no.:
Battery charger SBC4.5A - Article no.:
Battery charger SDBC2.4A - Article no.:
Battery charger SDBC4.5A - Article no.:
StarterKit SBSK2.0 - Article no.:
StarterKit SBSK4.0 - Article no.:
www.scheppach.com
7909201708
7909201709
7909201710
7909201711
7909201712
7909201713
7909201720
7909201721
Publicidad
