Publicidad
Idiomas disponibles
Idiomas disponibles
Most electrical accidents are caused by carelessness or ignorance. If you combine a basic knowledge of electricity, a healthy respect
for it, and a dose of common sense, you can safely tackle many household electrical repairs. Here are some basic guidelines for
working with electricity:
Before working on a circuit, go to the main service panel and remove the fuse or trip the breaker that controls that circuit. Tape a sign to the
panel warning others to leave the circuit alone while you work.
Before touching any wire, use a voltage tester to make sure it's not live.
Whenever you check for voltage in a receptacle, check both outlets – each may be controlled by a separate wiring circuit.
When replacing fuses, turn off the main power first. Make sure your hands and feet are dry, and place one hand behind your back to prevent
electricity from making a complete circuit through your chest. Touch a plug fuse only by its insulated rim. Remove cartridge fuses with a
fuse puller.
Use tools with insulated handles and ladders made of wood or fiberglass.
Keep dry-chemical fire extinguishers in the kitchen, basement, and workshop.
Never disable grounding devices. Make sure that all appliances requiring grounding are properly grounded, and that the electrical system
itself is properly grounded.
Meet or exceed all electrical code requirements that cover the work you are doing.
Always work with enough light to see what you are doing; it's easy to make mistakes when you're working in dim light.
If in doubt, consult a qualified electrician.
RF Exposure
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and
operated with a minimum distance 20cm between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Responsible Party: Globe Electric
Address: 2264 East 6th Street, San Bernardino, CA 92410 U.S.A.
www.globe-electric.com
CAN ICES-005 (B)/NMB-005 (B)
CAN ICES-003 (B)/NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development (ISED)
Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
The device has been evaluated to meet general RF exposure requirement.
The distance between user and products should be no less than 20 cm.
WARNING: to reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
WARNING: to reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the blades, or
cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: to reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "acceptable for fan support of
15.9/22.7/31.8 kg (35/50/70 lbs) or less" and use mounting screws provided with the outlet box.
CAUTION: to reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing light kit.
WARNING
READ AND SAVE THESE INSTRUCTIONS
3
Publicidad
