Allen + Roth HARTFORD WSLVCKJ Instrucciones De Ensamblaje página 3

HARDWARE CONTENTS (shown actual size)
AA BB
M6 x 40 mm M6 x 60 mm
Bolt Bolt
Qty. 14 Qty. 2
FF GG HH
M3.5 x 12 mm Large Wood Barrel Nut
Wood Screw Dowel (not shown to size)
Qty. 18 Qty. 8 Qty. 6
KK LL
L-Bracket Handle Small Cam Lock
(not shown to size) (not shown to size) (not shown to size)
Qty. 8 Qty. 1
PP QQ
M4 x 25 mm Wall Anchor
M6 x 10 mm
Screw (not shown to size)
Screw
Qty. 4
Qty. 4
UU VV
M4 x 38 mm Large Cam Lock
Screw (not shown to size)
Qty. 8 Qty. 4
CC DD
Lock Washer Small
Flat Washer
Qty. 16 Qty. 16
II
M8x 2-1/2 in. Large Flat
Lag Bolt
Qty. 4
MM NN
Small Cam Bolt Small Wood
(not shown to size)
Qty. 4 Qty. 4
RR SS
Allen Wrench Touch-up Pen
(not shown to size) (not shown to size)
(not included for Item
Qty. 8 Qty. 1
#811207, 2416442)
Qty. 1
WW VA
Large Cam Bolt M4 x 14 mm
(not shown to size) Wood Screw
Qty. 4 Qty. 24
4
HARDWARE CONTENTS (for pole kit)
EE
VB
Shelf Pin
M4 x 14 mm
Zinc Wood Screw
Qty. 8
Qty. 9
JJ
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install
Washer
the product.
• Do not allow children to climb or play in or around this product.
Qty. 4
• Use this unit for its intended purpose only. Do not use shelves as step ladder.
• To avoid damage, assemble the product on a sturdy, level and protective surface.
OO
• Two or more persons must work together to install the unit onto the wall.
• Make sure all bolts/screws are tightly fastened before the unit is used.
• Check bolts/screws periodically and tighten them if necessary.
• Unit must be permanently fastened to the wall with provided hardware; This storage
unit is not designed or intended for freestanding use.
Dowel
Qty. 8 WARNING
UNIT IS INTENDED FOR USE ONLY WITH MAXIMUM WEIGHTS INDICATED.
OVERLOADING STORAGE UNIT WITH PRODUCTS HEAVIER THAN MAXIMUM
TT
WEIGHT MAY RESULT IN INJURY. DISTRIBUTE ANY WEIGHT IN UNITS EVENLY.
• Shelf maximum load: 30 lbs.
• Pole maximum load: 40 lbs.
• Pole maximum length: 60 in.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble
the product.
Estimated Assembly Time: 120 minutes
Tools Required for Assembly (not included): Phillips Screwdriver, Power Drill, 3/16 in. Drill Bit, 3/8 in.
Drill Bit, 1/2 in. Socket Wrench, Level, Stud Finder, Marking Pencil, Tape Measure, Step Ladder, and
Hammer.
YO YC
Open Pole Closed Pole M4 x 15 mm
Holder Holder Self-tapping Screw
Qty. 3 Qty. 3 Qty. 6
5
YY ZZ
M4 x 38 mm
Zinc Screw
Qty. 9