Publicidad
Idiomas disponibles
Idiomas disponibles
Step 1:
Step 2:
The 021-7022 allows for safe and hands free climbing on vertical structures. In the event of an accident, any fall will be immediately arrested. It is necessary to use
this device in combination with a shock absorber to be ANSI Z359.15-2014 compliant. The user must always ensure they are at a lower level than the 021-7022.
Maximum working angle between user and device must not exceed 30°. The 021-7022 when used as part of a complete VLL system has a maximum capacity for
one user of up to 420 lbs.
User must ensure the VLL does not come into contact with any sharp or abrasive surfaces. The 021-7022 will automatically trail the user as they move up and
down the VLL. To stop the trailing function of the 021-7022 rotate the locking lever to PARK/REST position. As the user needs to move up or down the VLL, they
must rotate the locking lever back to the GO position.
To remove the 021-7022 from the VLL, disconnect the carabiner from the connection slot of the grab and rotate the front plate open. DO NOT ATTEMPT TO
DISCONNECT WHILE IN USE!!
FALL PROTECTION SYSTEMS MUST BE SELECTED AND INSTALLED UNDER THE SUPERVISION OF A COMPETENT PERSON AND USED IN A
COMPLIANT MANNER. FALL PROTECTION SYSTEMS MUST BE DESIGNED IN A MANNER COMPLIANT WITH ALL FEDERAL, STATE, AND SAFETY
REGULATIONS. FORCES APPLIED TO ANCHORS MUST BE CALCULATED BY A COMPETENT PERSON.
IF EQUIPMENT IS EXPOSED TO CHEMICAL HAZARDS THAT MAY CAUSE ANY DAMAGE OR DEGRADATION, EQUIPMENT MUST BE REMOVED FROM
SERVICE. IF IN DOUBT, CONTACT SAFEWAZE.
EQUIPMENT SUBJECTED TO FORCES OF A FALL ARREST MUST IMMEDIATELY BE REMOVED FROM USE.
12.6 DRIFT ROPE GRAB INSTALLATION AND OPERATION
1.
User must inspect the 022-7025 for any obvious signs of damage or defects prior to each use. Figure 13 illustrates the components of the 022-7025.
2.
User must be aware of, and seek to minimize, any swing fall hazards that may exist.
3.
Ensure adequate fall clearance exists for the equipment being used and associated work operations
4.
Rotate the sliding plate open by pushing the green plate gate to the left, while simultaneously pressing the red button. (Dwgs. 1 & 2). The 022-7025 was
designed for maximum efficiency and allows the sliding plate to open and close without removing the carabiner from the grab.
5.
Verify the position of the mode control switch is in the Trail position (Dwg. 3). With the sliding plate open, install the drift grab onto the VLL, ensuring the device
remains in the correct vertical orientation designated by an UP arrow (Dwg. 4).
6.
Rotate the sliding plate closed over the VLL. Make sure the red dot warning indicator is not visible on the plate gate (Dwg. 5).
7.
When used with an ANSI compliant Energy Absorbing Lanyard (EAL), the energy absorber's snap hook attaches directly to the User's Dorsal D-ring, with the
D-ring end of the lanyard attaching to the rope grab's carabiner. Connect the EAL to the installed rope grab's carabiner. (Dwg. 6).
8.
Pull upward on the connector to verify that the rope grab moves freely along the lifeline (Dwg. 7).
9. Proper function of the 022-7025 can be tested by again pulling up on the connector, and then rapidly pulling downward to ensure the grab locks onto the rope
and stops (Dwg. 8).
Step 3:
FIGURE 13 - COMPONENTS
Green Sliding
VLL Anchor Point
Ø 7/16" (11-12mm)
Kernmantle Rope
Free End of VLL
V5.0 2023 Copyright Safewaze
Step 4:
WARNING
Sliding Plate
Gate
Mode
"UP" Arrow
Control
Switch
Step 5:
Step 6:
022-7025
Connection Slot
Plate Lock
(Red Button)
STOP!
Page 12
Publicidad
