Craftsman 917.376721 Manual De Usuario página 6

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Engine Power Rating Information
The gross power rating for individual gas engine models is labeled in accordance with SAE (So-
ciety of Automo-tive Engineers) code Jl1940
(Small Engine Power & Torque Rating Procedure),
and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision
2002-5).
Actual gross engine power will be lower and is affected by, among other things, ambi-
ent operating conditions and engine-to-engine
variability. Given both the wide array of products
on which engines are placed and the variety of environmental
issues applicable to operating the
equipment, the gas engine will not develop the rated gross power when used in a given piece of
power equipment (actual "on-site" or net horsepower).
This difference is due to a variety of factors
including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel
pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude),
and engine-to-engine
variability.
Due to manufacturing and capacity limitations, Briggs & Stratton
may substitute an engine of higher rated power for this Series engine.
Read these
instructions
and this manual
in
Operator
its entirety
before
you attempt
to assemble
I
control bar
or operate
your new lawn mower.
IMPORTANT:
This lawn mower
is shipped
WITHOUT
OIL OR GASOLINE
in the engine.
Your new lawn mower has been assembled
at the factorywith
the exception
of those parts
left unassembled
for shipping
purposes.
To
UP
ensure safe and proper operation
of your lawn
mower, all parts and hardware
you assemble
must be tightened
securely.
Use the correct
tools as necessary
to ensure
proper
tight-
ness. All parts such as nuts, washers,
bolts,
etc., necessary
to complete
the assembly
have been placed
in the parts bag.
TO REMOVE
MOWER
FROM
CARTON
1.
Remove loose parts included with mower.
2.
Cut down two end corners
of carton
and lay end panel down flat.
3.
Remove
all packing
materials
except
padding
between
upper and lower
handle
and padding
holding
operator
presence
control
bar to upper handle.
4.
Roll lawn mower
out of carton
and
check
carton thoroughly
for additional
loose parts.
HOW TO SET UP YOUR MOWER
TO UNFOLD
HANDLE
IMPORTANT:
Unfold handle
carefully
so
as not to pinch or damage
control
cables.
1.
Raise handles
until lower handle sec-
tion locks into place in mowing
position.
2.
Remove
protective
padding,
raise up-
per handle
section
into place on lower
handle
and tighten
both handle
knobs.
3.
Remove handle padding holding operator
presence
control
bar to upper handle.
Your lawn mower
handle
can be adjusted
for your mowing
comfort.
Refer to "AD-
JUST
HANDLE"
in the Service
and Adjust-
ments section
of this manual.
/
//
/
//
/
MOWING
POSITION
Upper
handle
/ /
/
/
Handle
knob
Lower handle
TO ASSEMBLE
GRASS
CATCHER
1. Put grass catcher
frame
into grass
bag
with rigid part of bag on the bottom.
Make sure the frame
handle is outside
of the bag top.
2.
Slip vinyl bindings
over frame.
NOTE:
If vinyl bindings
are too stiff, hold
them in warm water for a few minutes.
If
bag gets wet, let it dry before
using.
b --¢ _,
/ -b _
Frame
_//\
_,,_/_
_
' handle
Vinyl
Frame
bindings
opening
TO INSTALL
ATTACHMENTS
Your lawn mower was shipped
ready to be
used as a mulcher.
To convert
mower to
bagging
or discharging,
see "TO CON-
VERT MOWER"
in the Operation
section
of this manual.

Publicidad

Tabla de contenido
loading

Tabla de contenido