Publicidad
Idiomas disponibles
Idiomas disponibles
Assembly
Note: You will need a power drill for the installation
work.
Note: Please also follow the instructions for your
power drill.
WARNING!
Please be sure not to drill into
any electrical wiring, gas or water lines inside the wall.
Installing the product
Note: Remove all packaging materials from the
ceiling fan with LED light.
21
□
Fasten the fan blades
20
holders
using the nuts
ers, washers and screws
□
Remove the pre-installed screws
3
housing
.
□
Attach the fan blade holders
3
ing
. To do this, use spring lock washers and
3a
the screws
pre-installed on the rotor housing
3
. Make sure that all the fan blades
either the side with the wenge effect or the white
site facing downwards (see Fig. B).
□
Before continuing with the installation, remove the
fuse or switch off the circuit breaker (0 setting) in
the fuse box.
□
Unscrew the right-hand fixing screw
ing the washer and tooth lock washer, which is
located at the side of the mounting bracket
Unscrew the left-hand fixing screw
the washer and the tooth lock washer. Mark the
drill holes using the holes in the mounting bracket
19
intended for the screws
□
Now drill the fixing holes. Make sure that you do
not damage the power cord (external)
pipes or electrical cables.
14
□
Insert the dowels
into the drilled holes (see
Fig. C). If necessary, use a hammer to help you.
IMPORTANT! Before mounting the ceiling
fan, make sure that the mounting location has a
load capacity of at least 45 kg.
□
Guide the power cord (external)
intended central hole in the mounting bracket
19
. Attach the mounting bracket
10 GB/IE/NI/CY/MT
to the fan blade
13
, spring lock wash-
12
(see Fig. A).
3a
on the rotor
20
to the rotor hous-
21
have
15
, includ-
19
.
15
including
11
as a guide.
22
, water
22
through the
19
using the
washers, spring lock washers and screws
provided (see Fig. C).
□
Using one of the holes intended for this purpose,
2
hang the cover
on the hook
19
ing bracket
(see Fig. D).
□
Connect the power cord (external)
17
lustre terminal
in the mounting bracket
Please also make sure that the colours of the con-
nected wires match (black or brown live wire = L
symbol, blue neutral wire = N symbol, protected
ground wire = green-yellow (see Fig. D)).
□
Insert the connection cable
19
bracket
into the connection cable port
the ceiling fan (see Fig. E).
2
□
Remove the cover
from the hook
2
□
Now place the cover
19
by guiding the fixing screws
grooves on the cover and then turning the cover
2
clockwise (see Fig. F).
□
Now screw the product and the mounting bracket
19
together using the four fixing screws
the spring lock washers and tooth lock washers.
Ensure that it is positioned correctly. The nose
must correspond with the groove (see Fig. G).
9
□
Screw the light bulb
7
(see Fig. H).
10
□
Attach the lampshade
Use the pre-installed thumb screws
purpose (see Fig. I).
CAUTION! Do not use pliers to tighten the
5
thumb screws
. This could cause the glass
10
of the lampshade
to crack. This could lead
to injuries caused by splinters of glass.
□
Replace the fuse or switch on the circuit breaker
(I setting) in the fuse box.
Your ceiling fan with LED light is now ready to use.
Initial use
Switching the LED light on and off
(see Fig. J)
8
□
Pull on the pull switch
11
18
on the mount-
22
with the
19
.
16
of the mounting
1
on
18
.
on the mounting bracket
15
into the
15
and
clockwise into the socket
4a
on the light unit
.
5
for this
to switch the LED light on.
Publicidad
