Publicidad
Idiomas disponibles
Idiomas disponibles
7.2
Inserting/removing the battery
(17) in the battery mount (18)
(Fig. 1, 7)
Inserting the battery
1. Push the battery (17) into the battery mount (18).
The battery (17) clicks into place audibly.
Removing the battery
1. Press the unlock button (16) of the battery (17) and
remove it from the battery mount (18).
7.3
Mounting the protective cover
(15) for cutting (Fig. 6)
ATTENTION
When cutting with bonded abrasives, always use the
protective cover for cutting.
1. Switch the product off and remove the battery as
described in Inserting/removing the battery (17) in
the battery mount (18) (Fig. 1, 7).
2. Push the protective cover (15) onto the cover (4)
until it engages.
3. When removing, the protective cover (15) must be
pulled forward slightly in order to release it.
7.4
Adjusting the protective cover (4)
(Fig. 2, 5)
WARNING
Always use the angle grinder with the protective cov-
er. The protective cover must be attached securely to
the angle grinder. Adjust it so that the highest degree
of safety is achieved, i.e. the smallest possible part of
the grinding wheel is revealed to the operator. The
protective cover is intended to protect the operator
from fragments and accidental contact with the grind-
ing wheel.
WARNING
Make sure that the protective cover is mounted at
least at the same angle as the additional handle. Oth-
erwise, you can be injured on the roughing and cut-
ting wheel.
1. Rotate the protective cover (4) into the required po-
sition (working position). Make sure that the protec-
tive cover (4) is positioned so that the protective
cover fixing (12) sits above one of the 5 cambers
(13) of the protective cover (4) (Fig. 5).
ATTENTION
Make sure that the protective cover fixing sits firmly in
the respective camber.
7.5
Mounting/changing the roughing/
cutting wheel
ATTENTION
Always wear protective gloves when changing the
roughing/cutting wheel.
–
Observe the dimensions of the roughing or cutting
wheels.
–
The diameter of the hole must fit the receptacle
flange without play.
–
Do not use reduction pieces or adapters.
Note:
Always use dirt-free discs.
WARNING
Danger of injury!
Only press the spindle locking button when the recep-
tacle spindle is stationary.
1. Push the spindle locking button (5) to block the
gear.
2. Undo the clamping nut (6) using the two-hole as-
sembly key (9).
3. Place the roughing or cutting wheel onto the recep-
tacle flange (7) with the labelled side facing the
product.
4. Then place the clamping nut (6) back onto the re-
ceptacle spindle (8) with the raised side facing up-
wards.
7.5.1
Note:
The collar of the clamping nut points upwards so that a
thin grinding disc can be clamped securely.
1. Push the spindle locking button (5) to block the
gear.
2. Tighten the clamping nut (6) using the two-hole as-
sembly key (9) again.
7.5.2
* = not included in the scope of delivery!
Note:
The collar of the clamping nut points downwards so that
the grinding disc can be attached securely to the recep-
tacle spindle.
1. Push the spindle locking button (5) to block the
gear.
2. Tighten the clamping nut (6) using the two-hole as-
sembly key (9) clockwise.
Note:
If the disc runs unevenly or vibrates after changing, this
disc must be replaced immediately.
www.scheppach.com
If the grinding disc is thin (Fig. 3, 4)
If the grinding disc is thick (Fig. 3,
4)
GB | 27
Publicidad
