Mitsubishi Electric TRANE HVAC US NTXCKS A112 Serie Manual De Instalación página 12

7. Electrical work
Service menu
Test run
Input maintenance info.
Settings
Check
Others
Main menu: RETURN
Cursor
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Fig. 7-11
Function setting
Ref. address
Unit No. Grp./1/2/3/4/All
Monitor: SELECT
Cursor Address
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Fig. 7-13
Function setting
Grp.
Ref. address
Mode 1
Mode 2
Mode 3
Mode 4
Request: SELECT
Cursor Cursor
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Fig. 7-15
Fig. 7-17
Fig. 7-19
11
Settings menu
Function setting
Service menu: MENU
F1 F2 F3 F4
RETURN SELECT
MENU
HOLD
Fig. 7-12
Function setting
Ref. address Grp.
Mode 1
Mode 2
Mode 3
Mode 4
Cursor Cursor
F1 F2 F3 F4
RETURN SELECT
MENU
HOLD
Fig. 7-14
Function setting
Ref. address Grp.
Sending data
F1 F2 F3 F4
RETURN SELECT
MENU
HOLD
Fig. 7-16
Fig. 7-18
B
Fig. 7-20
7.3. Function settings
7.3.1. By wired remote controller
1 (Fig. 7-11)
• Select "Service" from the Main menu, and press the [SELECT/HOLD] button.
• Select "Settings" from the Service menu, and press the [SELECT/HOLD]
button.
2 (Fig. 7-12)
• Select "Function settings" with the [SELECT/HOLD] button.
3 (Fig. 7-13)
ON
• Set the indoor unit refrigerant addresses and unit numbers with the [F1]
OFF
through [F4] buttons, and then press the [SELECT/HOLD] button to confi rm
the current setting.
<Checking the Indoor unit No.>
When the [SELECT/HOLD] button is pressed, the target indoor unit will start fan
operation. If the unit is common or when running all units, all indoor units for the
selected refrigerant address will start fan operation.
4 (Fig. 7-14)
• When data collection from the indoor units is completed, the current settings
appears highlighted. Non-highlighted items indicate that no function settings
are made. Screen appearance varies depending on the "Unit No." setting.
5 (Fig. 7-15)
• Use the [F1] or [F2] button to move the cursor to select the mode number, and
ON
change the setting number with the [F3] or [F4] button.
OFF
6 (Fig. 7-16)
• When the settings are completed, press the [SELECT/HOLD] button to send
the setting data from the remote controller to the indoor units.
• When the transmission is successfully completed, the screen will return to the
Function setting screen.
ON
OFF
7.3.2. By wireless remote controller
1 Going to the function select mode
Press the button between of 5 seconds.
(Start this operation from the status of remote controller display turned off .)
[CHECK] is lighted and "00" blinks. (Fig. 7-17)
Press the button to set the "50".
Direct the wireless remote controller toward the receiver of the indoor unit and
A press the button.
2 Setting the unit number
Press the button to set unit number A. (Fig. 7-18)
Direct the wireless remote controller toward the receiver of the indoor unit and
press the button.
3 Select a mode
button to set Mode number B. (Fig. 7-19)
Press the
Direct the wireless remote controller toward the receiver of the indoor unit and
press the button.
Current setting number:
4 Selecting the setting number
Use the button to change the Setting number C. (Fig. 7-20)
Direct the wireless remote controller toward the receiver of the indoor unit and
press the button.
5 To select multiple functions continuously
C
Repeat select 3 and 4 to change multiple function settings continuously.
6 Complete function selection
Direct the wireless remote controller toward the sensor of the indoor unit and press
the button.
Note:
Make the above settings on units as necessary.
• Table 1 summarizes the setting options for each mode number.
• Be sure to write down the settings for all functions if any of the initial settings
has been changed after the completion of installation work.
1=1 beep (1 second)
2=2 beep (1 second each)
3=3 beep (1 second each)