Milwaukee 48-22-8536 Manual Del Operador página 3

GROUNDING
Improperly connecting the ground-
WARNING
ing wire can result in the risk of
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the chest/cabinet. Never remove the
grounding prong from the plug. Do not use the
chest/cabinet if the cord or plug is damaged. If
damaged, have it repaired before use. If the plug
Chests/Cabinets with Three Prong Plugs
Chests/cabinets marked "Grounding Required"
have a power strip with a three wire cord and three
prong grounding plug. The plug must be connected
to a properly grounded outlet (See Figure A). If the
power strip should electrically malfunction or break
down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk
of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding sys-
tem in the power strip. The green wire in the cord
must be the only wire connected to the power strip's
grounding system and must never be attached to an
electrically "live" terminal.
Your power strip must be plugged into
an appropriate outlet, properly in-
stalled and grounded in accordance
with all codes and ordinances. The
plug and outlet should look like those
Fig. A
in Figure A.
ASSEMBLY
Be sure to follow the assembly in-
CAUTION
structions for the appropriate
chest/cabinet. Do not use power tools to as-
semble chest/cabinet. Tighten bolts with hand
wrenches.
Tools Required (Not Included)
Phillips Safety 10 mm
screwdriver goggles Wrench
Hardware Included
NOTE: Items not shown in actual size. Hardware
lengths are approximate.
Hardware Item Description
AA Bolt M6 x 16L
BB Steel washer
CC Bolt M8 x 18L
DD Screw M4 x 12L
EE Screw M4 x 16L
FF Screw M6 x 16L
Item Description
Side handle
5" Swivel caster
with brake
5" Rigid caster
Bracket
Front bumper
Rear bumper
Chest corner extrusion
13 mm
Wrench
Cabinet corner extrusion
Cord storage bracket
Bottle opener
NOTE:
intended location of your chest/cabinet. This product
4
Attaching the Side Handle
Attach the side handle to the rolling cabinet using
four bolts (AA). The side handle can be attached to
either side of the rolling cabinet, but must match the
Quantity
end where the swivel casters are installed.
NOTE: The holes in the cabinet are tapped and do
4
not require nuts.
16
16
20
20
2
Quantity
Installing the Casters
1
Two people may be required to
CAUTION
complete installation.
Do not overtighten the screws.
2
1. Ensure all cabinet drawers are securely locked into
place using the key lock on the rolling cabinet.
2. Lay the rolling cabinet on its back. Use the
2
3. Mount the two swivel casters with brake to the
rolling cabinet using four bolts (CC) and washers
(BB) per caster. The swivel casters with brake
must be installed on the end of the cabinet with
2
the side handle.
4. Mount the two rigid casters to the opposite end
of the rolling cabinet using four bolts (CC) and
8
washers (BB) per caster.
5. Tighten all bolts securely with a wrench.
2
6. Return the rolling cabinet to its upright position.
2
2
4
1
BB
CC
Installing the Chest onto the Cabinet
Two people may be required to
CAUTION
complete installation.
1. Place the top chest on top of the rolling cabinet.
NOTE: The holes in the cabinet are tapped and do
not require nuts.
2. Attach the two brackets to the back of the product
to secure the top chest to the rolling cabinet. Place
the brackets over the holes and secure with four
screws (DD) per bracket.
3. Tighten all screws securely with a Phillips screw-
driver.
AA
DD
Installing the Drawer Liners and Mat
Place the drawer liners in appropriately sized draw-
ers and the mat in the chest lid area to protect the
surface.
Installing the Corner Extrusions
and Bumpers
Place the front bumpers on both ends of the extrusion
by sliding the extrusion into the cavity of the bumpers.
Attach the front bumpers with extrusions using two
screws (EE) per bumper.
Attach the two rear bumpers to the back of the lower
cabinet using two screws (EE) per bumper.
EE
5