EINHELL TP-HD 18/26 Li BL Manual De Instrucciones Original página 16

The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................... 18 V DC
Idling speed: .....................................0-1200 min
Clockwise/counter-clockwise: ........................Yes
Blow rate: ........................................ 0-5500 min
Blow strength: ..............................................2.6 J
Drilling capacity concrete/stone (max.): ... 26 mm
Weight: .......................................................2.9 kg
Important!
The equipment is supplied without rechargeable
batteries and without a charger and is allowed to
be used only with the lithium-ion batteries of the
Power X-Change series!
The lithium-ion batteries of the Power X-Change
series are allowed to be charged only with Power-
X chargers.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 93.6 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ..................... 104.6 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Impact drilling in concrete
Vibration emission value a
K uncertainty = 1.5 m/s
Anl_TP_HD_18_26_Li_BL_SPK13.indb 16 Anl_TP_HD_18_26_Li_BL_SPK13.indb 16
-1
-1
= 15.139 m/s
2
h
2
- 16 -
GB
Chiseling
Vibration emission value a
K uncertainty = 1.5 m/s
2
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
prolonged period or is not properly guided
and maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).
= 14.175 m/s
2
h
20.12.2022 11:06:45 20.12.2022 11:06:45