Descargar Imprimir esta página

EINHELL TP-HD 18/26 Li BL Manual De Instrucciones Original página 17

Taladro percutor a batería

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 88
5. Before using the equipment
Be sure to read the following information before
you put the cordless impact drill into operation:
1. Charge the battery pack only with a charger
from the Power X-Change series.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Using a cable/pipe detector, check the area
you want to work on for concealed electric
cables and gas and water pipes.
5.1 Additional handle (Fig. 2/Item 6)
For safety reasons you must only use the im-
pact drill with the additional handle.
The additional handle (6) enables you to achieve
better stability whilst using the impact drill. For
safety reasons the machine must not be used wit-
hout the additional handle (6).
The additional handle (6) is secured to the impact
drill by a clamp. Turning the handle anti-clockwise
(viewed from the handle) will release the clamp.
Turning the handle clockwise tightens the clamp.
Release the clamp of the additional handle fi rst.
Then you can swivel the additional handle (6)
into the most comfortable working position for
yourself. Now turn the additional handle (6) in the
opposite direction again until the additional hand-
le (6) is secure.
5.2 Depth stop (Fig. 3 – Item 7)
The depth stop (7) is held in place with the lo-
cking screw (a) on the additional handle (6) by
means of a clamp.
Undo the locking screw (a) and fit the depth
stop (7).
Set the depth stop (7) to the same level as
the drill bit.
Pull the depth stop (7) back by the required
drilling depth.
Retighten the locking screw (a).
Now drill the hole until the depth stop (7) tou-
ches the workpiece.
5.3 Inserting a tool (Fig. 4)
Warning! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the equipment.
Clean the tool before fitting it and apply a thin
coating of bit grease to the tool shaft.
Anl_TP_HD_18_26_Li_BL_SPK13.indb 17
Anl_TP_HD_18_26_Li_BL_SPK13.indb 17
GB
Turn and push the dust-free tool into the tool
mounting (b) as far as it will go. The tool will
lock automatically.
Check that the bit is locked in placed by
pulling on it.
5.4 Removing a tool (Fig. 5)
Pull back and hold the locking sleeve (1) and re-
move the tool.
5.5 Charging the LI battery pack (Fig. 6/7)
1. Remove the battery pack (c) from the handle,
pressing the pushlock button (d) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(g) into the socket outlet. The green LED will
then begin to fl ash.
3. Push the battery pack onto the battery
charger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
voltage at the power socket
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
the charger and charging adapter
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
- 17 -
20.12.2022 11:06:46
20.12.2022 11:06:46

Publicidad

loading

Este manual también es adecuado para:

45.142.65