Johnson GreenBrite JDT300-GN3D Guia De Inicio Rapido

Quick Start Guide: Model No. JDT300-GN3D & JDT300-GN5D / Guide de rapide prise en mains : Modèles n° JDT300-GN3D &
JDT300-GN5D / Guía de inicio rápido: N.º de modelo JDT300-GN3D y JDT300-GN5D
Thank you for purchasing this GreenBrite® 3 or 5 Dot Laser! We want to get you up and
running as quickly as possible – but this quick start guide is not a replacement for reading and
understanding your operator's manual. For complete safety and operating instructions, refer to
the operator's manual.
Merci d'avoir acheté ce niveau GreenBrite® 3 ou 5 Dot
à laser ! Nous souhaitons que vous soyez opérationnel
le plus rapidement possible, mais ce guide de rapide
prise en mains ne remplace pas la lecture et la
compréhension de votre manuel d'utilisation. Pour
obtenir des instructions complètes sur la sécurité et
l'utilisation, reportez-vous au manuel d'utilisation.
¡Gracias por comprar este láser de 3 o 5 puntos
GreenBrite®! Queremos que empiece a trabajar lo antes
posible, pero esta guía de inicio rápido no reemplaza la
lectura y comprensión del manual del operador. Para
conocer las instrucciones de operación y seguridad
completas, consulte el manual del operador.
INSTALLING ALKALINE BATTERIES
1. Ensure the locking compensator is in the locked (OFF)
2. Rotate the laser so the rear of the unit is accessible.
3. Push down on the battery door lock tab to unlock and open the battery door. Remove the
alkaline battery case from the unit. See figure 1.
4. Slide the cover off the battery case and insert three "AA" alkaline batteries into the case
according to the polarity illustrated inside. See figure 2.
5. Reinstall the cover and reinsert the battery case into the unit. Be sure the end with the
openings is inserted first. Push the battery cover closed until it snaps shut.
Figure 1 / Figure 1 / Figura 1
position.
Figure 2 / Figure 2 / Figura 2
MOUNTING POSITIONS
Place the unit in an upright position, either on a
stable, flat surface, mount it to a tripod with a
1/4"-20 threaded screw, mount it to a ferrous surface
using the magnets, or hang it on a nail using the
mounting hole. Non-mar rubber feet on the unit
prevent damage to surfaces. See figure 3.
Use with the magnetic floor mount for easy
wall plumb applications. Slide the mount under
the integrated base of the unit until the locking
mechanism of the mount is engaged. To release the
magnetic floor mount from the unit, push down on
the release tab on the back of the mount and slide
the mount and integrated base apart. See figure 4.
Mounting Track
Rail de montage
Riel de montaje
Front Facing Magnets
Aimants orientés vers l'avant
Imanes orientados hacia adelante
Figure 4 / Figure 4 / Figura 4
OPERATION / AUTOMATIC MODE
1. Slide the locking compensator/power switch to the left to
the unlocked (ON) position to power on the unit. NOTE:
The unit must be within ±4° of level for the self-leveling
feature to function properly. If the unit is beyond its 4°
self-leveling range, the laser will not self-level, the laser
will flash, and the level indicator status light will flash red.
2. Slide the locking compensator to the right to the locked
(OFF) position to power off the unit. See figure 5.
Download full manual at / Téléchargez le manuel complet sur / Descargue este manual en
Mounting Hole
Trou de montage
Orificio de montaje
Mounting Magnets
Aimants de
montage
Imanes de montaje
Non-mar
Rubber Feet
Pieds en
caoutchouc
anti-marques
Patas de goma
antiarañazos
1/4"-20 Screw Thread
Filetage de vis 1/4 po-20
Rosca del tornillo 1/4"-20
Figure 3 / Figure 3 / Figura 3
Release Tab
Languette de dégagement
Lengüeta de liberación
Figure 5 / Figure 5 / Figura 5
www.johnsonlevel.com/manuals
JDT300-GN3D & JDT300-GN5D
©2024 Johnson Level & Tool