Publicidad
• Yardistry components are intended for privacy, decorative and ornamental use only. Product is NOT
INTENDED for the following:
- A safety barrier to prevent unsupervised access to pools, hot tubs, spas, or ponds.
- Safety railings for elevated platforms or decks.
- As load bearing support for a building, structure, heavy objects or swings. - Used in structures that trap
wind, rain or snow that would create extra load on the product.
• Permanent structures may require a building permit. As the purchaser and or installer of this product you
are advised to consult local planning, zoning, and building inspection departments for guidance on applicable
building codes and or zoning requirements.
• Wood is NOT flame retardant and will burn. Grills, fire pits and chimneys are a fire hazard if placed too
close to a Yardistry structure. Consult user's manual of the grill, fire pit or chimney for safe distances from
combustible materials.
• During installation, follow all safety warnings provided with your tools and use OHSA approved safety
glasses.
• Some structures may require two or more people to install safely. Check for underground utilities
before digging or driving stakes into the ground!
General Information: Wood components are manufactured with Cedar (C. Lanceolata) which is protected with
factory applied water-based stain. Knots, small checks (cracks) and weathering are naturally occurring and do
not affect the strength of the product. Annual application of a water-based water repellent sealant or stain will help
reduce weathering and checks.
Tools Required
Warranty: Yardistry Limited products are backed by a 5 year limited lifetime warranty from the date of original
retail purchase for manufacturing defects and if installed as per manufacturer's installation instructions.
• Tape Measure
• Carpenters Level
• Carpenters Square
• Claw Hammer
• Standard or Cordless Drill
• Tape Measure
Part Identification Key
• Carpenters Level
On each page, you will find the parts and
• Carpenters Square
quantities required to complete the assembly
step illustrated on that page. Here is a sample.
• S tandard or Cordless
Drill
Symbols
Throughout these instructions symbols are provided as important reminders for proper and safe assembly.
This identifies information that requires special
attention. Improper assembly could lead to an
unsafe or dangerous condition.
Use
Use
Help
Help
Measure
Check that assembly is square
Distance
before tightening bolts.
Use a measuring tape to assure
proper location.
CAUTION – Protrusion Hazard
!Important Safety Notice!
Keys to Assembly Success
• #1, #2 & #3 Phillips
or Robertson Bits
Patents Pending
or Screwdriver
• Ratchet with extension
Tools Required
(1/2" & 9/16" sockets)
• # 2 Phillips or Robertson
Bits or Screwdriver
2X A1 Post 2 x 4 x83"
• 1/8" Drill Bit
• Pencil
Quantity
• 8' Step Ladder
Keys To Assemble Success
Where this is shown, 2 or 3
people are required to safely
complete the step. To avoid
injury or damage to the
assembly make sure to get help!
Square
Assembly
• Open End Wrench
(7/16", 1/2" & 9/16")
• Adjustable Wrench
• 1/8" & 3/16" Drill Bits
• Pencil
• Safety Glasses
• Adult Helpers
Key Number
Check that set or assembly is properly level
before proceeding.
Pre-drill 1/8" & 3/16" Bit
Pre-drill a pilot hole
before fastening screw
or lag to prevent
splitting of wood.
This indicates time to tighten bolts, but
not too tight! Do not crush the wood.
This may create splinters and cause
structural damage.
No
If Bolt protrudes
2
beyond T-Nut
• 3/16" Hex Key
• 8' Step Ladder
• Safety Glasses
• Adult Helpers
Part Description, Part Size
Use
Level
Tighten
Bolts
Yes
Publicidad
