Surtek CN606A Manual De Usuario página 17

9. Attach the Right Fender (25A), with its wide
end at the top, to the right side of the Tapping
Plate (26A), using two Carriage Screws (16A),
two Washers (18A), and two Nuts (19A).
NOTE: The flanges on the Tapping Plate should
be facing outward.
10. Attach the Left Fender (29A), with its wide
end at the top, to the left side of the Tapping
Plate (26A), using two Carriage Screws (16A),
two Washers (18A), and two Nuts (19A).
11. Then, attach the Left Protective Plate (28A)
to the Right Fender (25A) and Left Fender
(29A), using four Carriage Screws (16A), four
Washers (18A), and four Nuts (19A).
12. Set the assembled Dust Chute aside until
after the Motor (33A) has been connected to
the unit.
13. Connect the bottom of the Upright Plate
(4A) to the Crossbeam Plate (17A), using two
Carriage Screws (16A), two Washers (18A), and
two Nuts (19A) (See Figures 4 & 5).
Fig. 4
4A
30A
4A
17A
Fig. 5
14. The Motor (33A), fastens to the Upright
Plate (4A). Insert four Cap Head Screws (SA)
through the bracket on the Motor, and then
through the Upright Plate. Temporarily, loosely
secure the Motor to the Upright Plate, using
four Washers (7A), four Lock Washers (30A),
and four Nuts (6A) (See Figure 6).
15. To connect the Motor's Electrical Cord to
the Switch (14A), and to connect the Cable
(36A) to the Switch, refer to the Wiring Dia-
gram.
Fig. 6
16. To attach the Switch (14A), insert the
Switch in the rectangular hole located on the
upper/right corner of the Front Plate (15A).
Secure the Switch to the Front Plate, using two
Machine Screws (11A), two Washers (12A), and
two Nuts (13A) (See Figure 9).
17. Retrieve the previously assembled Dust
Chute assembly with its attached Left Protec-
tive Plate (28A). Also, locate the Upper Link
Plate (2A).
18. Position the Dust Chute assembly so that its
upper flange rests on top of the upper flange
of the Upright Plate (4A). Then, position the
Upper Link Plate (2A) on top of the Dust Chute
5A
assembly flange. Connect the Upper Link Plate,
7A
Dust Chute assembly flange, and Upright Plate
30A
together, using two Carriage Screws (16A), two
6A
Washers (18A), and two Nuts (19A) (See Figures
5 & 7)
16A
18A
Fig. 7
19A
Placa de
unión
superior
2A
pestaña
16A
18A
19. Locate the Right Protective Plate (SA) and
19A
secure it to the right side of the body of the
Stand, using four Fixed Knobs (27A) and four
Screws (35A) (See Figure2).
20. Locate the Top Plate (1A) and attach it to
the Upper Link Plate (2A) on the right side of
the Stand. Insert two Carriage Screws (16A)
downward through the holes (located at the
right/front and right/rear) of the Top Plate and
through the holes located at each end of the
Upper Link Plate. Secure the Carriage Screws
with two Washers (18A) and two Nuts (19A).
E N G L I S H •
U se r ' s m an ua l
16A
18A
19A
4A
17