Publicidad
Idiomas disponibles
Idiomas disponibles
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store
or Google Play™ from a smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and
ready to be configured via the
ONE-KEY™ app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
WARNING
Selecting Air Speed
To increase or decrease the air flowspeed, use the
air speed control buttons. Press the - to decrease
the air flow speed, and press the + to increase the
airflow speed.
Automatic Filter Cleaning
The dust extractor has an automatic filter cleaning
system. For improved performance, it is recom-
mended to turn on automatic filter cleaning when
using the dust extractor. Press the filter cleaning
button to turn on the filter cleaning function. The filter
cleaning system will clean the filters about every 15
seconds during use.
Manual Filter Cleaning
During extremely heavy or long uses, manual clean-
ing may be necessary.
To manually clean the filter:
1. Turn on dust extractor.
2. Turn on automatic filter cleaning.
3. Place the palm of your hand over the hose end for
about 30 seconds.
4. Turn off the dust extractor.
5. If manual cleaning does not restore full suction,
replace the filter.
Low Airflow
The low airflow LED will light and an alert tone is
played when an obstruction occurs and continues to
play until obstruction is cleared or the dust extractor
is turned off.
Starting and Stopping Dust Extractor
To start the dust extractor, press the On/Off button
on the tool, on a paired remote, or start a paired
VACLINK™ tool.
To stop the dust extractor, press the On/Off button
on the tool, on a paired remote, or stop a paired
VACLINK™ tool.
Always wear proper eye
protection marked to
comply with ANSI Z87.1.
Using VACLINK™
When using VACLINK™, one person must control
both the dust extractor and the paired remote or tool.
If the extractor becomes clogged, the operator must
®
be able to turn the extractor off to prevent damage
to the extractor.
1. Once paired, set up the vacuum hose, work area,
and job as needed, following the tool and vacuum
instructions.
2. Turn on the tool. VACLINK™ will automatically
turn on the vacuum.
3. Turn off the tool and the vacuum will automatically
turn off after a short delay.
4. See Troubleshooting if tool and vacuum do not
operate as expected.
Pausing VACLINK™
VACLINK™ can be paused to halt the connection.
NOTE: When the tool's battery pack is removed
and then reinstalled, the pause is cancelled and
VACLINK™ will be active.
To pause or unpause, quickly press and release the
pairing button (<1 second)
VACLINK™ LED:
• Paused - Flashes red, then off
• Unpaused - Flashes red, then solid green
Picking Up Dry Materials
Make sure that the tank is dry before using the
dust extractor to pick up dry materials. If the dust
extractor tank is wet, run the dust extractor for about
5 minutes (without picking up anything) to dry the
inside of the tank.
Picking Up Wet Materials
WARNING
unless tank has been cleaned of dust and the
dust bag has been removed. Turn off the extrac-
tor if foam or liquid escapes from the tool.
1. WARNING! Unplug and remove batteries to avoid
starting the tool.
2. Release the tank latches and remove the motor
housing.
3. Remove dust bag and clean tank.
4. On the underside of the motor housing, ensure the
overfill sensors are dry and clean of debris. The
overfill sensors shut off suction when the tank is full.
5. Replace motor housing and latch in place.
6. Turn on the dust extractor.
7
To reduce the risk of
electric shock, DO NOT
pick up wet materials
Overfill sensor
Publicidad
