General Safety Instructions - Kreg TRACK HORSE Manual Del Propietário

WARNING
When using electric tools with this product, always follow the tool manufacturer's instructions in addition to the safety precautions below to reduce risk of
fire, electric shock, and personal injury. Read all these instructions before attempting to operate this product. SAVE THESE INSTRUCTIONS.
1) WORK AREA SAFETY
A) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
B) Don't use power tools in a dangerous environment. Don't use
power tools in damp or wet locations, or expose them to rain.
C) Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust.
Power tools create sparks that can ignite the fumes or dust.
D) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
E) Make your workshop child proof. Use padlocks,
master switches, or remove starter keys.
2) ELECTRICAL SAFETY
A) Ground electric tools. If the tool is equipped with a three-prong
plug, it must be plugged into a grounded three-hole electrical outlet.
If the proper outlet is not available, have one installed by a qualified
electrician. Never remove the third prong or modify the provided
plug in any way.
B) Do not expose power tools to rain or wet conditions.
Water entering a power tool increases the risk of electric shock.
C) Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
D) Use a proper extension cord and make sure it is in good
condition. When using an extension cord, be sure to use one
heavy enough to carry the current your power tool draws.
An undersized cord causes a drop in line voltage resulting in
loss of power and overheating. Table 1 shows the correct cord
gauge to use depending on cord length and tool nameplate
ampere rating. If in doubt, use the next heavier gage.
The smaller the gage number, the heavier the cord.
E) When operating electric tools, avoid body contact with
grounded or earthed surfaces such as pipes, radiators, kitchen
ranges, and refrigerators. Contact with a grounded surface
increases the risk of electric shock.
3) PERSONAL SAFETY
A) Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools can result
in serious personal injury.
B) Always wear safety glasses. Everyday eyeglasses are not safety
glasses. Safety glasses have specially constructed lenses, frames,
and side shields.
C) Use safety equipment. Use a face or dust mask when the cutting
operation is dusty. Safety equipment such as a dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate
conditions reduces personal injuries.
D) Avoid accidental starting. Make sure the switch is in the
off-position before plugging in. Carrying power tools with your
finger on the switch or plugging in power tools that have the
switch on invites accidents.
E) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating part
of the power tool can result in personal injury.
F) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
G) Secure workpieces. Use clamps or a vise to hold work when
practical. This is safer than using your hand and it frees both
hands to operate the tool.
H) Never stand on the machine. Serious injury can occur
if the tool tips or if the cutting tool is unintentionally contacted.
I) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts. Roll up long sleeves to
the elbow. Wear protective hair covering to contain long hair.
J) If devices are provided for the connection of dust extraction
and collection equipment, ensure these are connected and
properly used. Use of these devices reduces dust-related hazards.

GENERAL SAFETY INSTRUCTIONS

4) POWER TOOL USE AND CARE
5) SERVICE
6) SAFETY INSTRUCTIONS SPECIFIC TO THE KREG TRACK HORSE
A) Keep guards in place and in working order.
B) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
C) Use the right tool. Don't force a tool or
attachment to do a job for which it was not designed.
D) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
E) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
F) Never leave a tool running unattended. Turn power off.
Do not leave the tool until it comes to a complete stop.
G) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool and these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
H) Maintain power tools. Check for misalignment or binding
of moving parts, broken parts, and any other condition that can
affect power tool operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly
maintained power tools.
I) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
J) Use the recommended speed for the cutting tool
or accessory and workpiece material.
K) Only use parts and accessories recommended by the
manufacturer. Consult the owner's manual for recommended
accessories. Using improper accessories can cause personal injury.
L) Use the power tool, accessories, and tool bits in accordance with
these instructions and in the manner intended for the particular type
of power tool, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different
from those intended can result in a hazardous situation.
A) Have your power tool serviced by a qualified
repair person using only identical replacement parts.
This ensures that the safety of the power tool is maintained.
A) When deploying the legs, make sure the locking
pins are fully engaged in the leg-bracket holes.
Keep hands away from potential pinch points.
B) When adjusting leg height, make sure the
locking pins are fully engaged in the leg holes.
C) When folding the legs, do not trap hand between the leg
and the track. Keep hands away from potential pinch points.
D) Always work on a sturdy, dry, level surface.
E) When using power tools with the Track Horse,
follow the tool manufacturer's safety instructions.
F) When using two Track Horses in Table Setup, always support
workpieces on both 2x4 side rails or both Track Horses. Make sure
the saw blade does not contact the side rails or Track Horses.
G) When using two Track Horses in Cutting Setup, always
support workpieces on both 2x4 side rails and at least one
2x4 cross-member attached to the Track Horse T-track with
the provided hardware. Adjust the saw depth of cut to
deeper than the thickness of the workpiece.
H) The Track Horse is not intended for use
outdoors in damp conditions.
I) Always store the Track Horse inside or in an area sheltered from weather.
J) Do not use the Track Horse as scaffolding, a step,
or seat, or for any purpose not indicated in this manual.
K) Do not rest material on leg-extension locks.
L) Do not hang items from the Track Horse,
except as indicated in this manual.
⁄ " [3mm]
1
8