Taurus ICE BRISE SILENCE Instrucciones De Uso página 8

ASSEMBLING THE BATTERY/S OF THE REMOTE
CONTROL
• This appliance uses a 3V CR2025 battery.
• Caution: During the handling of batteries, do not touch
both poles at the same time, as this will provoke the
partial discharge of the stocked energy therefore affecting
longevity.
• Remove the cover of the batteries compartment.
• Check that the plastic covering that protects the batteries
has been removed (some batteries are sold with a
protective covering).
• Put the batteries in its compartment, respecting the
polarity.
• Replace the cover of the battery compartment.
• It is essential that the batteries should always be the
same kind and the same charge. Never mix alkaline
batteries with Carbon-Zinc ones and/or rechargeable
ones.
• Non-rechargeable batteries are not to be recharged.
• DO NOT charge rechargeable batteries while they are
still in the appliance as it may cause internal gas or heat
generation, resulting in an explosion or possibly a fire that
could cause serious injury or property damage.
• To preserve battery life, remove the batteries when it's not
being used, and is not expected to be used for extended
periods of time.
• WARNING: Danger of explosion if the battery is
incorrectly replaced.
• WARNING: DO NOT INGEST THE BATTERY;
CHEMICAL BURN HAZARD. This product contains a
coin/button cell battery. If the coin/button cell battery is
swallowed, it can cause several internal burns in just two
hours and can lead to death.
• Keep new and used batteries away from children. If the
battery compartment does not close securely, stop using
the product and keep it away from children.
• If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
• If the coin cell battery contents come into contact with
the skin, immediately wash the area with mild soap and
water. If coin cell battery liquid gets into the eyes, rinse
them with water over the open eye for 15 minutes or
until irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent and
lithium salts.
• Do not incinerate or dispose of tool together with
household waste material! Tool that has reached the end
of its life must be collected separately and returned to an
environmentally compatible recycling facility.
ASSEMBLING THE BASE
• Fit the base with the bottom tube and secure it with the
screw provided (R-S).
• Stand the base up again so as to check that the base
works properly.
• Fit the appliance with the top tube, and then with the
bottom tube, and secure it by using the lock nuts (L-O).
ASSEMBLING THE GRILL AND THE PROPELLER
• Fit the rear grill (G) on the motor housing (I), matching
their fitting points.
• Tight the grill nut (F) that attaches the grill. Make sure of
a correct setting.
• Fit the propeller (E) On the motor shaft (H).
• Tight the propeller nut (D) that attaches the propeller,
Make sure of a correct setting.
• Fit the front grill (A) front the rear grill (G). Fix the front grill
turning around its fixing belt and tight the security screw
by using a screwdriver.
• Check the correct rotation of the propeller.
INSTRUCTIONS FOR USE
BEFORE USE
• Make sure that all product's packaging has been
removed.
• Please read carefully the "Safety advice and warnings"
booklet before first use.
• Prepare the appliance according to the function you wish
to use.
USE
• Extend the supply cord completely before plugging it in.
• Connect the appliance to the mains.
• Guide the appliance to direct the flow of air in the desired
direction.
• Turn the appliance on, by using the on/off button, in the
control panel (3) or by the remote control (a).
• The current speed appears in the display (4).
• Select the desired speed by pressing the increase (c ) or
decrease (d) button, or increase the speed by repeatedly
pressing the speed button on the control panel (2) until
the desired speed is reached.
FAN FUNCTION
• You can select the speed by two ways:
- By selecting the desired speed (1-24) manually.
- By selecting the desired predefined mode (f-g-h).