Publicidad
Idiomas disponibles
Idiomas disponibles
Cleaning & maintenance
GB
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
Replacing the defective light
• ATTENTION! Always disconnect the appliance from the power
supply before replacement.
• Remove the old light and replace with a new one of the same
type (not included).
• If you do not sure how to replace, contact the supplier/service
provider. (See ==> Warranty)
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for clean-
ing. Do not use petrol or solvents!
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be carried
out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
10
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problem
Possible cause
The internal wires
are not connected
properly to the
electrical power
circuit system.
The wires of the
appliance are con-
Appliance not
nected to power
turned on.
circuit system but
not working at all.
ON / OFF switch
defective
Lamp bulb has
burned out.
No power to the
appliance
The appliance
is turned on but
ON / OFF switch
there is no light.
defective
Lamp bulb has
burned out.
The appliance is
mounted too high
to the target area.
Heat is inadequate
Incorrect lamp
bulb wattage.
The appliance is
mounted too close
to the target area.
Heat is excessive
Lamp bulb wattage
is too high.
Warranty
Any defect affecting the functionality of the appliance which
becomes apparent within one year after purchase will be re-
paired by free repair or replacement provided the appliance has
been used and maintained in accordance with the instructions
and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under war-
ranty, state where and when it was purchased and include proof
of purchase (e.g. receipt).
In line with our policy of continuous product development we
reserve the right to change the product, packaging and docu-
mentation specifications without notice.
Possible solution
Check again to
make sure it is
connected properly.
Turn on the appli-
ance by pressing
the switch at the "I"
position.
Contact the
supplier.
Replaced the bulb
with the same types
and same rating.
Check the circuit
breaker and reset
as necessary of the
system by qualified
technician.
Contact the
supplier.
Replaced the bulb
with the same type
and same rating.
Lower the mount-
ing height to closer
to the heated area.
Verify lamp bulb
and replace with
the correct wattage
bulb. Do not exceed
maximum lamp
bulb wattage.
Increase the
mounting height if
too close.
Check the bulb
wattage and
replace with lower
wattage bulb.
Publicidad
