Publicidad
Idiomas disponibles
Idiomas disponibles
the steam lever back to position
•
Wait until the steam completely stops before removing the
milk jug.
Place the steam wand in the "OFF" position after each use to
start automatic rinsing.
Barista tips: Fresh milk is recommended. Always use fresh milk
straight from the fridge.
For best results, always put the milk jug back in the fridge when
not in use.
Whole milk is recommended. The appearance and texture of
froth depends on the nature of the dairy milk or vegetable bev-
erages used.
After frothing the milk, eliminate unwanted bubbles by swirling
the jug gently.
Please note: During normal operation of the machine, some
water will be discharged in the drip tray to ensure optimal per-
formance.
After every use, remove any milk residue from the steam wand
with a soft damp cloth and place it in the "OFF" (auto clean) posi-
tion. The appliance delivers water from the steam wand.
A rinse is automatically performed when the appliance switches
off if the steam wand is left in position "A" (autosteaming).
If the wand is left in position "M" after steaming, the
indicator lights will blink to inform you of the need to place
the wand in the OFF position for automatic rinsing to be carried
out.
5. SETTINGS MENU
Press and hold the
(B1) and
to enter the settings menu. After a few seconds of inactivity, the
machine automatically exits the menu.
The
(B2) and (B3) indicator lights blink.
The following settings will be saved after a few seconds, when
the appliance automatically exits the settings menu.
5.1 Delay time between preinfusion and infusion
Increasing the delay changes the contact time between the wa-
ter and the coffee, thus changing the flavor profile.
To set the delay time, press the
No preinfusion delay
1 second (default)
2 seconds
5.2 Descale
To set the descale function, press the
(B3) indicator light blinks and the
on. Press and hold the
descaling (see instructions in the Descaling section) .
.
(B4) buttons for 3 seconds
(B1) button:
(B6) button; the
indicator light turns
(B6) button for 3 seconds to start
If descaling is accidentally activated, it can be stopped by press-
ing and holding the
5.3 Auto-off
To set the Auto-off time, press the
5 minutes (default)
1.5 hours
3 hours
If the machine is in Auto-off mode, press any button on the con-
trol panel to turn the appliance on.
5.4 Default values
To reset the default values press the
dicator light blinks. Press and hold the
seconds to reset all the settings.
All settings will be restored to the factory default.
5.5 Water hardness
To set one of the 3 water hardness levels, press the
button:
Water Hardness
Test Result
and
n
nn
nnn
nnnn (default)
5.6 Measuring water hardness
The
(B3) indicator light comes on following a preset period
of operation that depends on the water hardness setting. The
machine can also be programmed according to the actual hard-
ness of the local water supply, in which case descaling may be
required less frequently.
•
Remove the water hardness test indicator paper (A19)
•
Fully immerse the paper in a glass of water for one second.
•
Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water.
6. CLEANING
Important: Before servicing or cleaning the appliance, turn it
off, unplug it from the mains socket and allow it to cool.
Do not use solvents, abrasive detergents, or alcohol to clean
the coffee machine. Do not use metal objects to remove en-
crustations or coffee deposits as they could scratch the metal or
plastic surfaces. The drip tray, milk jug and small cup tray, are
9
(B6) button for at least 10 seconds.
(B7) button:
(B5) button; the in-
Corresponding
indicator light
medium water
hard or very hard water
from its pack.
(B5) button for 3
(B4)
Level
1
soft water
2
3
Publicidad
