Maxeon SunPower Reserve RESERVE-INV-1-P5-L1-INT Guía De Instalación Rápida página 3

Disassembling the Backup Plug Connector
Push to unlock
2 .5mm
1
4.3 BAT Power Connection
Danger to life due to burns caused by electric arcs through short-circuit currents .
Short-circuit currents in the battery can cause heat build-up and electric arcs . Heat build-up and electric arcs may
result in lethal injuries due to burns .
• Disconnect the battery from all voltage sources prior to performing any work on the battery .
• Disconnect the inverters from all voltages sources prior to performing any work on the inverter .
WARNING
• DO NOT short-circuit the battery terminals . First, complete the main negative terminal connection between
battery and inverter, and then complete the main positive terminal connection between battery and inverter .
• Observe all safety information provided in the Safety and Installation Instructions .
BAT+
BAT-
Battery packs 2-4
Battery Power Connection between
Inverter and RESERVE-BAT-1-DC-4-INT
Battery Power Connection on the Inverter side
1 .
click
②
①
Press the buckle with a fl at-head screwdriver
when unscrewing the swivel nut .
3 .
②
T20×150mm
4±0 .5Nm ③
④
①
RJ45 Socket
1 2 3 4 5 6 7 8
RJ45 Plug
T568B
Item No. 1 2 3
BMS NC RS485_A4 NC
RS485 12V NC GND
GRID_CT/ GRID_CT- GRID_CT+ RS485_A7
METER
PV_CT PV_CT- PV_CT+ RS485_A7
RRCR K1 K2 K3
DRM DRED1/5 DRED2/6 DRED3/7
AUX DO1_NO DO1_COM DO1_NC
5.3 Wiring the Communication Cables between Inverter (BMS) and Battery
Battery Communication Connection Battery Communication Connection
between Inverter and RESERVE-BAT-1-DC-4-INT between Inverter and RESERVE-1-DC-10 .1-INT
2 .5mm
2
2
3
+
_
_
+
_
+
_
+
Battery packs 1-6
Battery Power Connection between
Inverter and RESERVE-BAT-1-DC-10 .1-INT
2 .
①
③
2 .5×75mm
4 .
AUX
0 .5mm²
2
4
6
1
3
5
1 2
4 5 6 7
CAN1_H CAN1_L NC RS485_B4
RS485_B5 RS485_A5 NC NC
NC NC RS485_B7 NC
NC NC RS485_B7 NC
K4 3 .3V /
DRED4/8 REFGEN/0 COMLOAD/0
DI_ DI_POSITIVE GND
NEGATIVE
1 5
3
6
7
2
4
With
Terminal
Resistor
PV CT
Grid CT/Metter
RS485
BMS
4.4 PV Connection
1 .
1
7mm
7mm
3
4~6mm²
4 .
5.0 Communication Connection
5.1 Wi-Fi Module Connection
T20
5.2 Other Communication Connection
AUX/LAN/RRCR&DRM/PV-CT/GRID-CT&METER/RS485/BMS Connection
②
T20×150mm
5.4 CT Wiring
L N
F1
Grid
3
8
PE
NC
5.5 (Optional) For meter wiring, please refer to the Safety and Installation Instructions
NC
Manual
NC
NC
T20x150mm
1 .6Nm
6.0 Installing the Side Cover
1 .
1
3 .
Before turning on power, ensure that all the electrical connections are correct and reliable .
DANGER
2 .
Click
2 .6~2 .9Nm
Click
5 .
Click
Click
T20
M4*12
1 .6Nm
Keep the four screws on the COM
2
4
connection cover during disassembling .
3
1
Grid CT
PV CT (optional) PV Inverter
LOAD PV CT
L N
N
L
Grid CT
PE
2 .
2
4 .
T20x150mm
1 .6Nm
3 .
Check the polarity of the PV strings .
Check the open-circuit voltage of the PV strings which
should be less than 580V .
6 .
+
-
+
-
DRM PV_CT RS485
AUX LAN RRCR
GRID_CT/METER BMS
Pull with hand
3
3