Mitsubishi Electric TPKA0A0121LA10A Manual De Instrucciones página 9

3. Operation
3.5.2 Vane·Vent. (Lossnay)
<Accessing the menu>
Main Main menu
Operation
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Main menu: RETURN
Cursor
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
<Vane setting>
Fri
Off
Vane Vent.
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Fri
83
Room
Cool Set temp. Auto
83
Mode Temp. Fan
<Vent. setting>
Fri
Low
Vent.
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Select "Operation" from the Main
menu (refer to 3.5.1), and press the
[SELECT/HOLD] button.
Select "Vane·Louver·Vent.
(Lossnay)" from the Operation
menu, and press the [SELECT/
HOLD] button.
Press the [F1] or [F2] button.
Press the button as indicated above
to go through the following setting
options.
Auto
Auto Step 1 Step 2
Step 3 Step 4 Step 5
Swing
Swing
Select "Swing" to move the vanes
up and down automatically.
When set to "Step 1" through
"Step 5", the vane will be fixed at
the selected angle.
• under the vane setting icon
This icon will appear when the vane
is set to "Step 5" and the fan oper-
ates at low speed during cooling or
drying operation (depends on the
model).
The icon will go off in an hour, and
the vane setting will automatically
change.
Press the [F4] button to go through
the ventilation setting options in the
order of "Off ", "Low ", and "High".
* Settable only when LOSSNAY unit
is connected.
Off Low High
Off Low
• The fan on some models of indoor
units may be interlocked with cer-
tain models of ventilation units.
<Returning to the Main menu>
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Main menu: RETURN
Cursor
F1 F2 F3
RETURN SELECT
MENU
HOLD
Note:
●
During swing operation, the directional indication on the screen
does not change in sync with the directional vanes on the unit.
●
Available directions depend on the type of unit connected.
In the following cases, the actual air direction will differ from the
●
direction indicated on the remote controller display.
1. While the display is in "Standby" or "Defrost" states.
2. Immediately after starting heat mode (while the system is wait-
ing for the mode change to take effect).
3. In heat mode, when room temperature is higher than the tem-
perature setting.
<[Manual] To Change the Airflow's Left/Right Direction>
* The louver button cannot be used.
• Stop the unit operation, hold the lever of the louver, and adjust to the
desired direction.
* Do not set to the inside direction when the unit is in the cooling or dry-
ing mode because there is a risk of condensation and water dripping.
Caution:
To prevent falls, maintain a stable footing when operating the unit.
3.6. Ventilation
For LOSSNAY combination
■
The following 2 patterns of operation is available.
• Run the ventilator together with indoor unit.
• Run the ventilator independently.
For wireless remote controller
• Running the ventilator independently is not available.
• No indication on the remote controller.
High
Press the [RETURN] button to go
back to the Main menu.
F4
ON
OFF
en
8