Publicidad
Idiomas disponibles
Idiomas disponibles
5. Before starting the equipment
Caution!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
Power-X-Change
•
18 V, 1.5 Ah, 5 lithium-ion cells
•
18 V, 2.0 Ah, 5 lithium-ion cells
•
18 V, 3.0 Ah, 10 lithium-ion cells
•
18 V, 4.0 Ah, 10 lithium-ion cells
•
18 V, 5.2 Ah, 10 lithium-ion cells
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Warning!
Always remove the batteries before making ad-
justments to the equipment.
5.1 Fitting the blower tube (Fig. 3a/b)
Plug together the blower tube (Fig. 1) and the
motor unit (Item 3). Then lock the tube in place by
twisting it clockwise.
Important! The tube must be twisted as far as
the stop to ensure that it is locked securely.
5.2 Fitting the battery pack (Fig. 4)
Press the pushlock button of the battery pack as
shown in Fig. 4 C and push the battery pack into
the mount provided. When the battery pack is po-
sitioned as in Fig. 4b, make sure that the pushlock
button latches in place! To remove the battery
pack, proceed in reverse order.
Important!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two batte-
ries must always be fully charged before use.
5.3 Charging the battery (Fig. 5)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(D) into the socket outlet. The green LED will
then begin to blink.
Anl_SA_GE_LB_36_Li_E_Solo_SPK8.indb 23
Anl_SA_GE_LB_36_Li_E_Solo_SPK8.indb 23
GB
3. Insert the battery pack (E) into the charger
(D).
4. In section 11. „Charger indicator" you will fi nd
a table with an explanation of the LED indica-
tor on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless leaf blower
drops. Never fully discharge the battery pack. This
will cause it to develop a defect.
5.4 Fitting the harness (Fig. 3c/3d)
Fasten the harness (Fig. 3c / Item 4) to the eyelet
(Fig. 3c / Item A) on the motor housing. Place the
harness over your shoulder and adjust the length
to that you can guide the equipment comfortably.
Caution: Carry the harness so that the click
fastener is always within reach. In an emer-
gency you can quickly remove the equipment
by opening the click fastener (Fig. 3d / Item
B).
6. Operation
6.1 Switching on the equipment (Fig. 6)
•
To switch on, press and hold the On/Off
switch (2).
•
To switch off, let go of the On/Off switch.
•
Channel the air stream forward and walk
slowly to blow foliage or garden refuse into a
pile or to clear out hard-to-reach places.
- 23 -
06.02.2018 13:14:02
06.02.2018 13:14:02
Publicidad
