Publicidad
Idiomas disponibles
Idiomas disponibles
EnglISH
The RBRC® Seal
Please take your spent battery packs to an
authorized BLACK+DECKER service center
or to your local retailer for recycling. In some
areas, it is illegal to place spent battery packs
in the trash. You may also contact your local recycling center
for information on where to drop off the spent battery pack.
Do not place in curbside recycling. For more information
visit www.call2recycle.org or call the toll-free number in
the RBRC® Seal.
RBRC® is a registered trademark of Call 2 Recycle, Inc.
SAVE THESE INSTRUCTIONS
ASSEMBLY
WARNING:
repair the appliance.
Wall Mounting (Fig. B–E)
The product can be wall mounted, if desired, using the wall
mount bracket, screws and anchors supplied. To wall mount
the vac, refer to Fig. B–E.
• Figure B - Mark the location of the screw holes (within
reach of an electrical outlet for charging the vac while it is
on the wall bracket).
• Figure C - Insert the charger cord into the curved slot in
the wall mount bracket leaving approximately 8–9 inches
(203 mm - 227 mm) excess as shown.
• Figure D - Hang the vac on the wall by placing the
opening on the base of the vac over the hooks in the wall
mount bracket as shown.
• Figure E - Insert the jack plug into the charging socket.
Charging the Battery (Fig. F)
WARNING:
supplied charger.
From new, the rechargeable cells of the product need a
minimum charge time of 16 hours to ensure full power.
• The switch must be in the off ("O") position. The product
will not charge if it is in any other position.
• Figure F - Plug the jack plug of the charger into the
charging socket of the tool. Plug the charger into any
standard 120 Volt 60 Hz electrical outlet.
While charging, the charger may get warm; this is perfectly
normal and safe. It is safe to leave the appliance connected
to the charger indefinitely. The charger automatically
reduces power consumption when charging is complete.
WARNING:
ambient temperatures below 39°F (4°C) or above 104°F (40°C).
Use
Switching On and Off (Fig. G)
• Figure G - To start, slide the On/Off switch forward
(i.e., "O"= Off, "I" = On).
• To stop, slide the switch back.
• Return the product to the charger immediately after
use so that it will be ready and fully charged for the next
use. Ensure that the product is fully engaged with the
charger plug.
6
Do not attempt to modify or
For use only with the
Do not charge the battery at
Cleaning and Emptying the Product
WARNING:
Never use the vac without its filter.
nOTE: The filter is reusable so do not confuse it with a
disposable dust bag, and do not throw it away when the
product is emptied. We recommend that you replace the
filter every 6–9 months depending on frequency of use.
There are two methods of cleaning the bowl, a quick empty
method and a thorough clean method.
For a Quick Empty (Fig. H, I)
• Figure H - Press in on both nozzle release buttons on
the sides of the nozzle and remove the nozzle by pulling
straight off.
• Figure I - Empty the dust from the bowl.
For a More Thorough Cleaning (Fig. J, K)
• Figure J - Remove the dust bowl by pressing the bowl
release button and pulling the bowl straight off.
• Remove filter from within the bowl.
• Remove the cloth filter and shake or lightly brush any
loose dust off both filters.
• Figure K - The dust bowl and filter can be washed in
warm, soapy water. Allow to dry before placing back into
the vac.
• Place filter back into the bowl pressing firmly to ensure a
secure fit.
• To replace dust bowl, place it back onto the handle until it
"clicks" firmly into position.
IMPORTAnT: Maximum dust collection will only be
obtained with a clean filter and an empty dust bowl. If dust
begins to fall back out of the product after it is switched off,
this indicates that the bowl is full and requires emptying.
• Wash the filters regularly using warm, soapy water and
ensure that it is completely dry before using again. The
cleaner the filter is, the better the product will perform.
• It is very important that the filter is correctly in position
before use.
Cleaning Scented Filter (HHVI320JRS) (Fig. l)
• To separate the plastic filter
twist the plastic filter in a counterclockwise direction and lift
it off of the cloth filter as shown in Figure L.
• Shake or lightly brush any loose dust off both filters.
• The dust bowls and filters can be washed in warm, soapy
water. Allow to dry before placing back into the vac.
• To replace the filters, slide the outer plastic filter over the
cloth filter.
• Align the wings of the plastic filter with the slots in the
cloth filter and twist in a clockwise direction.
• Place filters back into the bowl pressing firmly to ensure
a secure fit.
• To replace dust bowl, place it back onto the handle until it
"clicks" firmly into position.
Nozzle/Accessories (HHVI320JR, HHVI320JRS,
and HHVI325JR) (Fig. M–O)
• Figure M - A crevice tool is built into the nozzle and can
be extended as shown by pulling the extension piece until it
locks into position.
• Figure N - A brush accessory is built into the nozzle and
can be flipped upwards for use.
Projectile/respiratory hazard:
14
from the cloth filter
15
,
Publicidad
