Publicidad
Idiomas disponibles
Idiomas disponibles
Important Safety Instructions and Precautions
WARNING:DO NOT CONNECT DIRECTLY TO THE PUBLIC SWITCHED
TELEPHONE NETWORK (PSTN). ANY CONNECTION OF THIS PHONE
TO AN OFF PREMISE APPLICATION, AN OUT OF PLANT APPLICATION,
ANY OTHER EXPOSED PLANT APPLICATION, OR TO ANY EQUIPMENT
OTHER THAN THE INTENDED APPLICATION MAY RESULT IN A SAFETY
HAZARD, AND/OR DEFECTIVE OPERATION, AND/OR EQUIPMENT
DAMAGE. "EXPOSED PLANT" MEANS WHERE ANY PORTION OF THE
CIRCUIT IS SUBJECT TO ACCIDENTAL CONTACT WITH ELECTRIC
LIGHTING OR POWER CONDUCTORS OPERATING AT A VOLTAGE
EXCEEDING 300 V BETWEEN CONDUCTORS OR IS SUBJECT TO
LIGHTNING STRIKES.
WARNING:THE SOCKET OUTLET, IF USED, SHALL BE LOCATED NEAR
THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE BY THE USER.
WARNING:USE MITEL APPROVED POWER ADAPTER MITEL PART
NUMBER 50005301.
NOTE: SOME LAN JACKS PROVIDE POWER AND DO NOT REQUIRE AN
AC POWER ADAPTER. IF POWER OVER THE LAN IS AVAILABLE, IT
SHALL BE COMPLIANT WITH IEEE 802.3af.
WARNING:THE HANDSET SUPPLIED WITH THE IP CONSOLE IS NOT
CERTIFIED FOR USE WITH ANY OTHER PHONE. USE OF THE
HANDSET WITH ANY OTHER PHONE MAY HAVE THE POTENTIAL TO
CAUSE HEARING LOSS IN THE EVENT OF A LIGHTNING STRIKE ON
THE OUTSIDE PLANT WIRING.
When using your phone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons, including
the following:
• Do not use this product near water, for example, near a bath tub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a swimming
pool.
• Avoid using a phone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
• Do not use the phone to report a gas leak in the vicinity of a leak.
Maintenance and Repair: There are no user serviceable parts inside Mitel
phones. For repairs, return the phone to an authorized Mitel dealer.
These notices may appear on the product or in the technical documentation:
Danger indicates an imminently hazardous situation which, if not
DANGER
avoided, will result in death or serious injury.
Warning indicates a potentially hazardous situation which, if not
WARNING
avoided, could result in death or serious injury.
Caution indicates a potentially hazardous situation which, if not
CAUTION
avoided, may result in minor or moderate injury and/or damage to the
equipment or property.
This symbol may appear on the product:
The exclamation point within an equilateral triangle indicates that important
operating and maintenance (servicing) instructions are included in the
!
literature accompanying the product.
Description
The 5540 IP Console is supported by the SX-200
(ICP) Release 5.0 and later software.
Using the IP Programmable Key Modules (PKM)
The 5540 IP Console supports the IP PKM 48. For installation information, refer
to the Installation Guide packaged with the IP PKM. For information on how to
use the IP PKMs, refer to the 5540 IP Console User Guide available at
www.mitel.com (see Supporting Documentation).
2
IP Communications Platform
®
Supporting Documentation
To access console- and system-specific documentation:
1. In your browser, go to www.mitel.com.
2. Click Resources and then select Guides.
3. Click User Guides.
4. In the left-hand menu, click on Consoles and navigate to SX-200 ICP.
Installing a 5540 IP Console (See Figure
Plug the LAN cable into the LAN port on the back of the console.
Plug the other end of the LAN cable into the network jack or DC adapter.
NOTE: In the absence of a Power-Over-Ethernet (POE) LAN switch, use a
qualified Mitel-supplied DC power adapter only.
Plug the handset cord into the handset port.
(Optional) Plug the headset cord into the headset port.
(Optional) Connect the jack for cordless support into the AUX port of the
cordless base station using the GN Cordless Headset Cable ordered from
Mitel.
NOTE:For cordless headset operation, refer to Installing a Cordless
Headset (Optional) below for full details.
Install the lens (see Installing and Removing the Lens below).
To register the phone, perform the following steps:
If prompted, enter a valid PIN, and then press (HOLD1) to register the phone.
After the date and time display, proceed with the next step.
(Optional) Connect a network device to the PC port. Allow up to several
minutes for the network connection to be established.
(Optional) Connect a IP PKM 48.
Installing and Removing the Lens (See Figure
The 5540 IP Console is shipped with the plastic lens and a fixed designation
card installed. An installer can also change the fixed designation card by
removing the lens and replacing the card.
The lens is held in place with four tabs, two along the upper edge and two along
the lower edge.
To remove the lens:
• Pull up on the lens on both the left and right side at the access cutouts.
Lens will bend across its length and the tabs will pull out and pop free from
the cutout slots.
• Remove the desi card by standing the console on its forward nose and
tipping it so the card drops out.
To replace a fixed designation card and lens:
Place the designation card over the keyboard keys and place the overlay
lens on top of the designated card by following step 2 below.
Place the lens over the keyboard area and insert the tabs along the upper
edge into the two tab slots at the top edge of the keyboard area.
Slightly bend the lens along its length, just enough to allow the bottom edge
tabs to engage into the slots at the lower edge of the keyboard area.
The lens should snap itself flat with all four tabs fully engaged into their
respective slots.
To Restore Factory Default Settings
1. Press both Volume Up and Volume Down Arrow keys simultaneously while
powering up the console. NETWORK PARAMETERS? appears.
2. Press NO until TOOLS & FEATURES appears and then press YES.
3. Press NO until RESTORE DEFAULTS? appears and then press YES.
4. Press CONFIRM. The console will reset with default settings.
A
)
B
)
Publicidad
