Publicidad
Idiomas disponibles
Idiomas disponibles
Setting for desired screw length (Fig. 5)
There are 3 positive-lock screw length settings. To obtain
the desired setting, pull out the stopper base while
depressing the lever until you see the number of the
desired screw length (indicated on the plate) appear to
rest on the very top edge of the casing. See the table
below for the relation between the number indicated on
the plate and the respective screw length ranges.
Number indicated
on the plate
25/28
32
40
Adjusting the driving depth (Fig. 6)
Depress the stopper base as far as it will go. While keep-
ing it in this position, turn the adjusting knob until the bit
tip projects approx. 5 mm from the stopper base. Drive a
trial screw. If the screw head projects above the surface
of the workpiece, turn the adjusting knob in the "A" direc-
tion; if the screw head is countersunk, turn the adjusting
knob in the "B" direction.
Installing screw strip
1.
Squeeze the lock lever with fingers and open the
magazine cap. (Fig. 7)
2.
Roll up the screw strip in a form of coil counterclock-
wise and place it inside the magazine. (Fig. 8)
3.
Run the end of the screw strip on the slotted pas-
sage starting from above the magazine. (Fig. 9)
4.
Close the magazine cap while squeezing the lock
lever with fingers. (Fig. 10)
5.
Insert the top end of the screw strip into the portion
A of the feeder box and feed it in the direction of the
arrow. (Fig. 11)
6.
Set the screw strip so that the first screw of the strip
seats with a space for one screw left before the
screw-driving position. (Fig. 12)
Removing the screw strip
When removing the screw strip at or before using up the
screws, pull it out in the direction of the arrow. (Fig. 13)
If you depress the reverse button, you can pull out the
screw strip in the reverse direction of the arrow. (Fig. 14)
Extension handle (optional accessory) (Fig. 15)
Use of extension handle allows you to drive screws into
floors while standing.
Screw length range
(mm)
25 – 28
28 – 35
35 – 41
OPERATION
Driving operation (Fig. 16)
Switch on the tool by pressing the trigger and at the
same time pushing the lock button. Hold the tool squarely
against the workpiece and apply forward pressure to the
tool. The screw will be automatically carried to the driving
position and driven into the workpiece.
NOTE:
• Do not fire the tool without screws. This will damage
the workpiece.
• If the feeder box becomes sluggish in operation, spray
car wax (spray type wax) on its sliding surfaces. Never
lubricate it.
Driving in corner (Fig. 17)
This tool can be used to drive at a position 15 mm away
from the wall as shown in Fig. 17.
CAUTION:
Driving at a position closer than 15 mm to the wall or driv-
ing with the stopper base in contact with the wall may
damage the screw heads and cause wear on the bit. This
may also lead to poor fastening of screws and malfunc-
tion of the tool.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Replacing carbon brushes (Fig. 18 & 19)
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Phillips bit
• Drywall screw strips
• Extension handle
• Plastic carrying case
7
Publicidad
