Publicidad
Idiomas disponibles
Idiomas disponibles
with another Wireless Tool Control™ device, such as a
D
WALT dust extractor.
e
1. To pair your tool using Wireless Tool Control™ first,
remove any mounted wheel. A spinning wheel can cause
injury.
2. Depress the trigger switch
hand on the main handle
holding the auxiliary handle
the pairing button on the separate device. An LED on
the separate device will let you know when your tool has
been successfully paired.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product,
e
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
WARNING: Do not use a bonded abrasive wheel that
is past its expiration (EXP) date as marked near center
of wheel, if provided. Expired wheels are more likely to
burst and cause serious injury. Store bonded abrasive
wheels in dry location without temperature or humidity
extremes. Destroy expired or damaged wheels so they
cannot be used.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
The capacity of this tool is 7" (180 mm) and 9" (228 mm)
diameter x 1/4" (6 mm) thick grinding or 3/16" (5 mm) thick
cutting wheels. It is important to choose the correct guards,
backing pads and flanges to use with grinder accessories.
1
. While holding with one
12
and the other hand firmly
5
, have someone else push
e
WALT. Call 1‑800‑4‑D
WALT
e
e
Refer to the Accessories Chart for information on choosing
the correct accessories.
WARNING: Accessories must be rated for at least
the speed recom mended on the tool warning label.
Wheels and other accessories running over their
rated accessory speed may fly apart and cause injury.
Threaded accessories must have a 5/8"-11 hub. Every
unthreaded accessory must have a 7/8" (22 mm)
arbor hole. If it does not, it may have been designed
for a circular saw. Use only the accessories shown in
the accessories Chart of this manual. Accessory
ratings must always be above tool speed as shown on
tool nameplate.
WARNING: Handle and store all abrasive wheels
carefully to prevent damage from thermal shock, heat,
mechanical damage, etc. Store in a dry protected area
free from high humidity, freezing temperatures or
extreme temperature changes.
Tool Connect™ Chip (Fig. S)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
Installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
WALT
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement) should be performed by a
D
WALT factory service center or a D
e
service center. Always use identical replacement parts.
ENGlIsH
that hold the Tool
24
into the tool.
22
23
.
WALT-authorized
e
51
Publicidad
