Whirlpool W6 D94WR SPT Guía Rápida

Quick guide
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.whirlpool.eu/register
PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO REACH MORE INFORMATION.
CONTROL PANEL
Programme selection knob
1
On/Off button
2
Start/Pause button
3
Options buttons
FreshCare+
4
Cycle End Signal
5
Rapid
6
Cycle Options (hold for Settings)
7
Dryness Level
8
Timed Drying
9
Start Delay
10
Navigation buttons and Key Lock
UP
11
DOWN
12
CONFIRM (hold for Key Lock)
13
INDICATORS
Cycle phase:
Drying -
Empty water tank -
Refer to Troubleshooting section:
FIRST TIME USE
When starting the appliance the first time, the control panel
will automatically show the set language menu. The UP and
DOWN buttons are used to show the languages available in
the machine. Press the button to confirm. The machine
cannot be used without having selected the language.
Make sure that the water tank is correctly inserted.
The dryer must be installed in a room with a temperature
ranging between 5°C and 35°C to ensure proper operation.
Before using the dryer make sure it has been in an upright
position for at least 6 hours. Should you wish to change the
opening side of the door, please contact our After-sales
Service. (See phone number in the warranty booklet).
DAILY USE
Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying cycle.
- remember to clean your filters after each drying cycle.
Refer to the Care & Maintenance section.
1. Plug the dryer into the power supply socket.
2. Open the door and load garments; always refer to instructions on
clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door filter. Do not load items that
are dripping wet. Do not tumble dry large, very bulky items. For
optimal drying result, garments should be loaded one by one.
3. Close the door.
4. Press the "On/Off" button.
5. Select the most suitable programme for the type of fabric in
that load.
6. Select the options, if necessary.
7. Press the "Start/Pause" button to begin drying.
8. At the end of the drying cycle, a buzzer will beep. An indicator
on the control panel signals the end of the cycle. Turn the
machine off by pressing the "On/Off" button, open the door and
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
pull the clothing immediately out to prevent the formation of
• Using QR code in your appliance
creases on laundry.
• Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com
If the machine is not switched off manually, after about a quarter
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales
of an hour from the end of the cycle , the appliance turns off
Service, please state the codes provided on your product's identifi cation plate.
automatically to save energy.
Note that some models perform a final cool tumble phase, for this
reason the fabrics may not feel hot.
In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
1
Cool Down
Clean secondary filter -
Failure call After-sales Service
Before using the appliance carefully Before using the appliance carefully
read the Safety Instruction. read the Safety Instruction.
5
6
7
8
Clogged door filters -
Eco Monitor
This indicator shows the energy consumption level according to
the programme and the options set. The consumption is
proportional to the lines on the display, by the ecomonitor icon.
Opening the door during the cycle
The tumble dryer door can be opened at any time during the cycle
to check progress and remove any garments already dry.
However, since opening the door can extend the drying time, the
recommendation is to keep the door closed throughout the cycle
process to save time and energy.
After closing the door, press the "Start/Pause" button within 15
minutes to resume the machine operation.
NOTE: in any case, the drying cycle must be completed to ensure
the condenser auto-cleaning phase is finalized.
NAVIGATION
The "UP" and "DOWN" buttons are used to navigate the available
menus.
• Press the button to confirm the selection.
• Press the option button at the
display, to return to the previous screen.
If no selection is confirmed, after about 10 seconds, the display
return to the main screen.
SETTINGS
To access the Settings menu, press and hold the relevant button for
a few seconds.
• Set language shows the available languages on the display.
• Sounds allows to enable or disable the sounds (some sounds, as
warnings, will remain active anyway).
• Brightness allows to modify the display brightness.
• Factory Default allows to reset the default settings. After having
selected the setting, press and hold the
seconds.
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the fi rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
1:35
SYNTHETICS
-:--
-:--
9 10
Autoclean - Eco Monitor
symbol, where present on the
EN
2
11
12
4
13
3
button for a few