Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLING/REMOVING BATTERY PACK
See Figure 3, page 12.
„ Set the switch in the OFF position.
„ Insert the battery pack into the product as shown.
„ Make sure the latches on each side of the battery pack
snap in place and that battery pack is secured in the
product before beginning operation.
„ Depress the latches to remove the battery pack.
For complete charging instructions, see the operator's
manuals for your battery pack and charger.
WARNING:
Battery tools are always in operating condition. Turn the
switch OFF when not in use or carrying at your side, when
installing or removing the battery pack, and when install-
ing or removing bits. Failure to turn off the switch could
result in unexpected starting and serious personal injury.
ATTACHING/REMOVING VACUUM ADAPTOR
See Figures 4 - 6, page 13.
WARNING:
During use, always keep vacuum hose clear of the path
of the bit.
The vacuum adaptor attaches to the router base for im-
proved dust management when used in combination with
a vacuum. The vacuum hose adaptor accepts 1-1/4 in. to
1-7/8 in. vacuum hoses.
NOTE: The router ships with a chip shield that must be
removed prior to installing the vacuum adaptor.
To remove the chip shield and install the vacuum adaptor:
„ Remove the battery pack.
„ Turn the router upside down to remove the four subbase
screws and the subbase.
„ Place your fingers inside the base and gently push out
on top of the chip shield near the tab until it snaps free.
„ Hold the vacuum adaptor at a slight angle and place it
onto the base so that the rounded edges of the adaptor
are aligned with the holes in the base.
„ Gently press the top of the vacuum adaptor until the tab
snaps into place.
„ Align the tabs on the subbase with the grooves in the
removable base, then place the subbase onto the remov-
able base.
„ Attach the subbase using the four subbase screws.
„ Tighten the screws securely. Do not over tighten.
OPERATION
WARNING:
Always use a subbase recommended for use with this
product when trimming. Use of the router without a sub-
base or using the incorrect subbase can result in serious
personal injury.
To remove the vacuum adaptor and install the chip shield:
„ Remove the battery pack.
„ Turn the router upside down to remove the four subbase
screws and the subbase.
„ Place your fingers inside the base and gently push out on
top of the vacuum adaptor near the tab until it snaps free.
„ Hold the chip shield at a slight angle and place it onto the
base so that the rounded edges of the shield are aligned
with the holes in the base.
„ Gently press the top of the chip shield until the tab snaps
into place.
„ Align the tabs on the subbase with the grooves in the
removable base, then place the subbase onto the remov-
able base.
„ Attach the D-shaped subbase using the four subbase
screws.
„ Tighten the screws securely. Do not over tighten.
STARTING/STOPPING THE ROUTER
See Figure 7, page 13.
To turn the router ON, slide the switch on front of the router
to the ON position.
Return the switch to the OFF position when finished.
WARNING:
The bit will continue to spin after the router is turned off.
Wait for the bit to come to a complete stop to continue
operation. Failure to do so could result in possible seri-
ous injury.
ADJUSTING THE SPEED
See Figure 8, page 13.
The variable speed dial is located on the front of the mo-
tor housing. The speed is adjustable from 15,000 RPMs to
30,000 RPMs.
„ Rotate the dial to higher numbers to increase speed.
„ Rotate the dial to lower numbers to decrease speed.
NOTE: Use higher speeds for smaller bits and cutters, soft-
woods, plastics and laminates. Use lower speeds for larger
diameter bits and cutters.
7 — English
Publicidad
