Publicidad
Idiomas disponibles
Idiomas disponibles
B70MP
8
*
19AB863
4.5) Return to original factory settings/firmware version
60°
9
*
Select screen 10 from the "main menu" (Ref. to § 4.1), to return the pump to its factory setting hold
max 90°
the finger on the button (4) until a confirmation "beep" is heard.
RESET
RY
ERROR
10
SW: S1K25102
4.6) Errors/Malfunctions
RY
These appear on the display during the operation, combined with a beep to notify the operator
11
001
of procedural or operational errors. They are accompanied by an audible signal and the CEMBRE
logo (8) lighting up yellow.
0001
002
Message
003
ET
1405
RY
ERROR
004
°
ax 90°
RY
001
ERROR
RY
0001
002
.
min.
RY
ERROR
NTC
RY
FAULT
ERROR
003
RY
ET
RY
ERROR
Y
BATTERY
1405
RY
RY
ERROR
001
004
°
0001
001
RY
BATTERY
RY
001
ax 90°
002
0001
001
RY
BATTERY
002
0001
001
ET
BEEP
002
30001
0001
003
1405
002
0001
003
ET
RESET
002
°
SW:S1J41405
1405
003
ET
min.
x.
004
90°
003
ET
1405
004
ax 90°
°
max 90°
1405
003
ET
004
°
RY
BATTERY
1405
ax 90°
004
°
ax 90°
max.
min.
004
°
ax 90°
EP
BATTERY
BATTERY
ax 90°
LED
x.
min.
ON
LED
Errors 00.. are displayed for about 30 seconds before being reset, but will display repeat-
BEEP
x.
min.
OFF
BEEP
RY
BATTERY
edly in the event of permanent anomalies.
.
min.
.
min.
Lorem ipsum
RY
BATTERY
ERCH OFF
.
min.
RY
BATTERY
RY
BATTERY
BEEP
RY
BATTERY
BEEP
EEP
BEEP
The RESET screen also shows the firmware version of the control board.
Error description
In CRIMPING mode, a 100 bar pres-
sure has been reached or exceeded
but the oil discharge has been acti-
vated before waiting for the motor
to be automatically switched off.
The pump has been started without
the flexible hose connected or the
flexible hose is not correctly con-
nected.
Interruption of the signal from
the NTC temperature probe of the
battery.
Abnormal power consumption of
LED
the motor.
ERROR
OFF
The pump stops.
LED
001
Output voltage of the pressure trans-
ON
mitter is out of the pre-set range.
002
The pump stops and doesn't re-start.
003
Failure to reach the set pressure
004
within 120 sec. of continuous opera-
tion of the pump.
Overcharging of the battery with
LED
protection tripping.
The pump stops.
OFF
LED
OFF
LED
LED
ON
ON
LED
OFF
LED
ERCH ON
LED
OFF
LED
OFF
LED
ON
LED
OFF
LED
Lorem ipsum
Lorem ipsum
S
olution
Repeat the work cycle, keeping the start but-
ton pressed down until the motor switches off
automatically.
Press the release button, connect the flexible
hose or check the correct connection to the
pump.
Replace the battery. If the problem persists,
please contact CEMBRE.
Wait for the display to turn off (60 sec.) or
remove and re-insert the battery, then re-
start the pump, if the problem persists, please
contact CEMBRE.
Remove and re-insert the battery, if the problem
persists, please contact CEMBRE.
Repeat the work cycle; if the problem persists,
please contact CEMBRE.
Wait for the display to turn off (60 sec.) or
remove and re-insert the battery, then re-
start the pump. if the problem persists, please
contact CEMBRE.
ERCH OFF
18
Publicidad
