Electronic Control Setup Instructions (Pd & Pn Models); General Information - Maytag MDE20PDAGW Instrucciones De Instalación

IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished,
but failure may occur at a later date due to ESD stress.
■ Use an anti-static wrist strap. Connect wrist strap to
green ground connection point or unpainted metal in the
appliance.
Touch your finger repeatedly to a green ground connection
point or unpainted metal in the appliance.
■ Before removing the part from its package, touch the
anti-static bag to a green ground connection point or
unpainted metal in the appliance.
■ Avoid touching electronic parts or terminal contacts;
handle electronic control assembly by edges only.
■ When repackaging failed electronic control assembly
in anti-static bag, observe above instructions.

General Information

BLANK DISPLAY – This condition indicates the dryer is
inoperative. Enter set-up mode to view diagnostic code.
"0 MINUTES" SHOWING IN DISPLAY – This indicates the
cycle is complete and the dryer cannot be operated. Coins
dropped or debit inputs during this condition will be stored in
escrow but cannot be used until normal operation is restored
by opening and closing the door. If a door switch has failed,
it must be replaced before normal operation can be restored.
COLD START (Initial first use) – Dryer is programmed at the
factory as follows:
5 minutes dry time/quarter (coin 1)
$1.50 dry price (fixed cycle with top off)
WARM START (after power failure) – A few seconds after
power is restored, if a cycle was in progress at the time of the
power failure, "RESELECT CYCLE" will flash in the display,
indicating a button needs to be pressed to restart dryer.
PRICING – After the door is opened and then closed following
the completion of a cycle, the display indicates the cycle price
(unless set for free operation). As coins are dropped or debit
inputs arrive, the display will change to lead the user through
the initiation of a cycle.
There are four (4) types of dryer pricing:
Fixed "Vend" Pricing
A dryer set up for "Fixed Cycle" operation can only accept
additional time accumulated by increments equal to the length
of a complete dry cycle. A maximum of 99 minutes may be
purchased; no additional credit is given for coins dropped with
99 minutes in the display.
ELECTRONIC CONTROL SETUP INSTRUCTIONS
-OR-
(PD & PN MODELS ONLY)
Accumulator Pricing
If the price is set to one coin 1, then accumulator pricing
is in effect. Cycle time can be purchased one coin at a time
up to the maximum time of 99 minutes. Stacked models will
credit all money to a cycle with a single button press while in
accumulator pricing.
Fixed Cycle With Top Off Pricing
A dryer set to offer "Top Off" capability will allow time to be
added to an existing dry cycle in increments equal to the
number of minutes of dry time per quarter (coin 1), up to 99
minutes, regardless of the cost required to start the dryer. No
credit is given for coins or debit inputs entered when the control
is displaying 99 minutes.
FREE CYCLES – This is established by setting the cycle price
to zero. When this happens, "SELECT CYCLE" will appear
rather than a cycle price. Any cycle started as a free cycle will
automatically terminate when the door is opened.
DEBIT CARD READY – This dryer is debit card ready. It
will accept a variety of debit card systems, but does NOT
come with a debit card reader. Refer to the debit card reader
manufacturer for proper dryer setup. In models converted to
a Generation 1 debit card system, debit pulses represent the
equivalent of one coin (coin 1).
Display
After the dryer has been installed and plugged in, the display
will show "0 minutes."
Single Load Models
Once the unit has been plugged in and the dryer door opened
and closed, the display will show the price.
Single Load Models
0
MINUTES
PRICE
1.50
21