Functional Description - Makita CL072D Manual De Instrucciones

9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties, for-
warding agents, special requirement on packaging
and labeling must be observed.
For preparation of the item being shipped, consulting
an expert for hazardous material is required. Please
also observe possibly more detailed national regula-
tions.
Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in
the packaging.
11. Follow your local regulations relating to disposal
of battery.
12. Use the batteries only with the products speci-
fied by Makita. Installing the batteries to non-com-
pliant products may result in a fire, excessive heat,
explosion, or leak of electrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries. Use of non-genu-
ine Makita batteries, or batteries that have been altered,
may result in the battery bursting causing fires, personal
injury and damage. It will also void the Makita warranty
for the Makita tool and charger.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot bat-
tery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before adjusting or checking
function on the tool.
Installing or removing battery cartridge
For Model CL072D (Fig. 1)
For Model CL102D (Fig. 2)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the
cartridge.
• To insert the battery cartridge, hold it so that the battery
cartridge front shape fits to that of the battery
installment opening and slip it into place. Always insert
it all the way until it locks in place with a little click. If
not, it may accidentally fall out of the tool, causing
injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Battery protection system
The cleaner is equipped with the protection system,
which automatically cuts off the output power for its long
service life.
The cleaner stops during operation when the cleaner
and/or battery are placed under the following situation.
This is caused by the activation of protection system and
does not show the cleaner trouble.
• When the cleaner is overloaded:
At this time, release the switch trigger and remove
causes of overload and then pull the switch trigger
again to restart.
• When the remaining battery capacity gets low:
Recharge the battery cartridge.
Switch action (Fig. 3)
To start the cleaner, simply press the "HIGH/LOW" but-
ton. To switch off, press the "OFF" button. To change the
cleaner speed, press the "HIGH/LOW" button. The first
press on this button is for high speed and the second
press for low speed and then each press on this button
repeats the high/low speed cycle alternatively.
Battery power lamp (Fig. 4)
• When the remaining battery capacity gets low, the bat-
tery power lamp blinks.
• When the remaining battery capacity gets much lower,
the tool stops during operation and the battery power
lamp lights up for about ten seconds. At this time,
remove the battery cartridge from the tool and charge
it.
NOTE:
• The time at which the battery power lamp start blinking
or lighting up depends on the temperature at work
place and the battery cartridge conditions.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work
on the tool.
Disposing of Dust (Fig. 5, 6, 7, 8 & 9)
CAUTION:
• Empty the cleaner before it becomes too full, or the
suction force weakens.
• Be sure to empty out the dust inside the cleaner itself.
Failure to do so may cause the sponge filter to be
clogged or the motor to be damaged.
• Never throw away the dust stopper because it should
be used whenever either the dust bag or the paper
pack is used.
1. Push the button to open the front cover. Opening it
until a click is heard allows a positive stop at that
position.
NOTE:
• The cleaner is constructed in such a way that the front
cover comes off when trying to force the front cover
open at the angle of more than 90°. If the front cover
comes off, insert it into the front cover joint in place.
CAUTION:
• When closing the front cover, be careful not to pinch
your fingers.
2. Pull out both the orange-colored dust stopper and
dust bag together at the same time.
3. Remove the dust stopper and empty the cleaner.
9